Manuals / Woodstock / Power Tools / Lathe

Woodstock M1109 Adjusting/Replacing the V-Belt, To replace or adjust the V-belts, do these steps

Models: M1109

1 74

Download 74 pages 21.8 Kb

Page 37

M1109 Combo Lathe/Mill

For daily lubrication, use a manual oil gun with a general 10W machine oil to lubricate the following 15 ball oiler fit- tings. See Figure 56 for some typical locations. Wipe off all oil ball fittings with a rag, and then oil the following locations:

•Cross Feed Table (1 ball oiler on top)

•Cross Feed Handwheel (1 ball oiler on top)

•Saddle Ways (2 ball oilers on top)

•Apron Handwheel Gear Axle (1 ball oiler on apron face)

•Compound Rest (1 ball oiler on top)

•Tailstock Barrel (1 ball oiler on top)

•Tailstock Handwheel (1 ball oiler on right side)

•Lead Screw Endcap Bushing (1 ball oiler, see Figure 57)

•Change Gear Spindle (1 ball oiler on end of shaft)

•Gear Spindle Ball Oiler (1 ball oiler, see Figure 55)

•Gearbox (4 ball oilers on top)

NOTICE

Failure to follow lubrication guidelines will lead to rapid deterioration of lathe/mill components.

Adjusting/Replacing the V-Belt

To replace or adjust the V-belts, do these steps:

1.DISCONNECT POWER TO THE LATHE/MILL!

2.Open the change gear access door (Figure 58).

3.Loosen the four motor access cover screws, and lift the cover off (Figure 58).

4.Using a 17mm wrench, loosen the two motor mount bolts shown in Figure 58.

5.Grasp the motor and lift upward to de-tension the belt and remove the belt.

6.Use solvent to clean the pulleys of oil and install the new belt.

7.Let the motor hang to tension the belt, and tighten the two motor mount bolts.

8.Close the access door and latch it shut.

-35-

Figure 56. Typical ball fitting locations.

Figure 57. Lead screw end cap bushing.

Motor

Mount

Bolts

Figure 58. Motor mount bolts.

MAINTENANCE

Image 37

Woodstock M1109 owner manual Adjusting/Replacing the V-Belt, To replace or adjust the V-belts, do these steps

Contents

Combo LATHE/MILL Page Contents Parts Introduction SpecificationsWoodstock Technical Support Controls and Features Standard Safety Instructions SafetySafety Additional Safety Instructions for Lathe/Mills Always protect the bed ways, Avoiding Potential Injuries220V Operation ElectricalExtension Cords GroundingInstalled Accessories Figure Qty SetupPackaged Accessories Figure InventoryMachine Placement Cleaning MachineTo unpack and move the lathe/mill, do these steps Uncrating and LiftingTroubleshooting on To begin the test run procedure, do these stepsTest Run and Break-In Lathe Operations Power SupplyGeneral Chuck and Faceplate Mounting Disconnect Power to the LATHE/MILLTo remove a set of jaws, do these steps Replacing JawsClamping workpiece Using the Four-Jaw ChuckFaceplate installed Using the FaceplateTo install the MT#3 drill chuck, do these steps Using the TailstockDrilling with the Tailstock To use the tailstock, do these stepsCutting Shallow Tapers With the Tailstock To setup the tailstock to cut tapers, do these stepsTailstock Alignment To align the tailstock, do these stepsTailstock adjustment option #2 To install a dead or live center, do these steps Using CentersUsing the Follow Rest Using the Steady RestTo use the steady rest, do these steps Using the Tool Post Setting Compound SlideTo set the angular position, do these steps Longitudinal Handwheel Using Manual FeedTo determine and set the needed cutting RPM, do these steps Setting RPMCutting Speeds for High Speed Steel HSS Cutting Tools Refer to the Change Gear Chart on Page 29, or Setting Power Feed RateTo setup for threading, do these steps Threading SetupLoosen the apron lock bolt and use the feed lever Figure Change Gear Chart To install a tool in the spindle, do these steps Installing ToolsMilling Operations Removing ToolsQuill Travel Headstock PositioningTo position the spindle head vertically, do these steps To use the quill, do these stepsTable Travel To begin the start up procedure, do these stepsHigh speed steel cutting chart General Maintenance MaintenanceGeneral Cleaning General LubricationTo replace or adjust the V-belts, do these steps Adjusting/Replacing the V-BeltCross Slide, Half-Nut Compound Slide Gib Adjustments ServiceCross Slide Backlash M1109 Electrical panel Electrical Component and Connection IndexContactor Electrical ConnectionsTransformer connection Lathe controls Wiring DiagramMotor & Electrical TroubleshootingOperation and Work Results Parts Diagram PART# Description Series Parts List1007 1028 Thread Dial DiagramSPANNERNUTM16-1.5 Leadscrew Gearbox Diagram 2000 Series Parts Coverplate Compound Rest and Tool Post Diagram FEMALEKNOB5/16-18 Bed Diagram 3000 Series Parts BED Steady Rest and Follow Rest Diagram Pinnedknob Apron Diagram XPK81M Tailstock Diagram STEELBALL8MM Mill Column Diagram XPLW05M LOCKWASHER12MM Headstock Diagram 7000 Series Parts XPR12M EXTRETAININGRING35MM Accessories and Labels Diagram 6THREE-JAWCHUCK Main Wiring Box Diagram Parts Warranty Comments Warranty RegistrationBOX BELLINGHAM, WA