MZ-N10
Ver 1.2 2003.02
Dimensions
Approx. 78.5 ⋅73.3 ⋅13.8 mm (w/h/d)
(31/8 ⋅3 ⋅9/16 in.) (excluding projecting parts and controls)
Mass
Approx. 84 g (3 oz) (including the
1)The LINE IN (OPT) jack is used to connect either a digital (optical) cable or a line (analog) cable.
2)The i/LINE OUT jack connects either headphones/earphones or a line cable.
3)Measured in accordance with JEITA.
4)Measured in accordance with the JEITA (Japan Electronics and Information Technology Industries Association) standard.
5)When using a 100% fully charged
6)When using a Sony LR6 (SG) “STAMINA” alkaline dry battery (produced in Japan).
Supplied accessories
AC power adaptor (1) USB cradle (1)
Headphones/earphones with a remote control (1) Dedicated USB cable (1)
Dry battery case (1) Optical cable (1)
Carrying pouch/carrying case with a belt clip (except USA model) (1) Recordable MD (USA and Canada models only) (1)
∗Do not play a
US and foreign patents licensed from Dolby Laboratories.
Design and specifications are subject to change without notice.
•SonicStage, OpenMG and the OpenMG logo, MagicGate, Memory Stick and the MagicGate Memory Stick logo, Memory Stick and the Memory Stick logo, Net MD and the Net MD logo are trademarks of Sony Corporation.
•Microsoft, Windows, Windows NT and Windows Media are trademarks or registered trademarks of Microsoft Corporation in the United States and /or other countries.
•IBM and PC/AT are registered trademarks of International Business Machines Corporation.
•Macintosh is a trademark of Apple Computer, Inc. in the United States and/ or other countries.
•MMX and Pentium are trademarks or registered trademarks of Intel Corporation.
•All other trademarks and registered trademarks are trademarks or registered trademarks of their respective holders.
•™ and ® marks are omitted in this manual.
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- LISHED BY SONY.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous ra- diation exposure.
On power sources
•Use house current, nikel metal hydride rechargeable battery, LR6 (SG) battery, or car battery.
•For use in your house: For the supplied battery charging stand, use the AC power adaptor supplied with this recorder. Do not use any other AC power adaptor since it may cause the recorder to malfunction
Polarity of the plug
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be dam- aged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270 ˚C dur- ing repairing.
•Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering or unsoldering.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead- free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•Unleaded solder melts at a temperature about 40 ˚C higher than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Soldering irons using a temperature regulator should be set to about 350 ˚C .
Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
•Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc.
•Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
2
