Sound Skip Check Result Display Mode
This set can display the count of errors that occurred during the recording/playing for checking.
•Setting method of sound skip check result display mode
1.Set the test mode (see page 11).
2.Press the N key or zREC. key, and the playing or re- cording sound skip check result display mode becomes active respectively and press the > key on the remote commander, and then the playing sound skip check result display mode becomes active where the LCD displays the following.
Remote commander LCD display
000P * * R * *
Total count of play | Total count of record |
system errors (hex.) | system errors (hex.) |
3.When the N key is pressed, total error count is displayed on the LCD, and each time the > key is pressed, the display item moves down by one as shown below. Also, if the . key is pressed, the display item moves up by one, then if the zREC. key is pressed, the display in the record mode appears.
When the zREC. key is pressed, total error count is dis- played on the LCD, and each time the > key is pressed, the display item moves down by one as shown below. Also, if the . key is pressed, the display item moves up by one, then if the N key is pressed, the display in the play mode appears.
Playing sound skip | Recording sound skip |
result display | result display |
000 P * * R * * | 000 P**R** |
000 EIB ** | 000 BOvr** |
000 Stat** | 000 Bful** |
000 Adrs** | 000 Rtry** |
000 BEmp** | 000 ###### |
000 ###### |
|
P**R**: Total play/record errors (hex.)
**: Counter of sound skip check each item (hex.)
######:
• Cause of sound skip error
| Cause of error | Description of error | |
| EIB | Sound error correction error | |
|
|
| |
Play | Stat | Decoder status error | |
|
| ||
Adrs | Address access error | ||
| |||
|
|
| |
| BEmp | Buffer is empty | |
|
|
| |
| BOvr | Buffer is full, and sounds were | |
| dumped | ||
|
| ||
|
|
| |
Record | Bful | Buffer capacity becomes less, | |
| and forcible writing occurred | ||
|
| ||
| Rtry | Retry times over |
4.To quit the sound skip check result display mode and to return to the test mode (display check mode), press the x key.
Key and Jog Check Mode
This set can check if the set and remote commander function nor- mally.
• Setting method of key check mode
1.Set the test mode (see page 11).
2.Pressing the [T MARK] key or [DISPLAY] key on the remote commander for several seconds (about 3 seconds) activates the key check mode. (At the last two digits, AD value of remote com- mander key line is displayed in hexadecimal)
Remote commander LCD display
000**
**: AD value of the remote commander key (hexadecimal 00 to FF)
3.When each key on the set and on remote commander is pressed, its name is displayed on the remote commander LCD. (The operated position is displayed for 4 seconds after the slide switch is operated. If any other key is pressed during this dis- play, the remote commander LCD switches to its name dis- play)
Example1: When the > key on the set is pressed:
Remote commander LCD display
000 FF **
**: AD value of the remote commander key (hexadecimal 00 to FF)
Example2: When the > key on the remote commander is pressed:
Remote commander LCD display
000 rFF **
**: AD value of the remote commander key (hexadecimal 00 to FF)
4.When all the keys on the set and on the remote commander are considered as OK, the following displays are shown for 4 sec- onds.
Example1: When the keys on the set are considered as OK:
Remote commander LCD display
888 SET OK **
Set LCD display
888
SET OK **
**: AD value of the remote commander key (hexadecimal 00 to FF)
15
