Marantz SR7002 FM Tuning Mode Auto Stereo or Mono, Auto Preset Memory, Manual Preset Memory

ENGLISH

(FM) TUNING MODE (AUTO STEREO OR MONO)

M

D1

D2

D3

D4

USE PAGE 2

D5

SURROUND
DIGITAL
AAC			VOL
CH
TV	DVD	VCR	DSS
TUNER	CD	CD-R	MD
TAPE	AUX1	AUX2	AMP
		LIGHT
1			2

RC8001SR

Learning Remote Controller

Analog Mono Mode

T - M O D E : M O N O

MONO mode is selected and the AUTO indicator disappears from the FL display. Monaural broadcasts are received in TUNER mode.

Note:

• On the SR7002, the TUNER mode cannot be

changed when BAND is set to AM.

• The SR7002 does not display the mode on the FL

display when the TUNER MODE is switched.

The AUTO indictor appears on the FL display when

the mode is switched to Analog Auto Mode. (See

PRESET MEMORY

With this unit you can preset up to 60 FM/AM stations in any order.

For each station, you can memorize the frequency and reception mode if desired.

AUTO PRESET MEMORY

This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory.

2. 4. 1. 3. 2. 5.

MANUAL PRESET MEMORY

3.2. 4.

SURROUND

DIGITAL

AAC

	LIP.SYNC
PREV		MUTE
	GUIDE
MENU		EXIT
TEST	CH.SEL	SURR
1	2	3	3.
7.1CH	ATT	SPK-AB
4	5	6
DISP	OSD	SLEEP
7	8	9	2.
	THX
CLEAR	0	MEMO

page 9)

AV SURROUND RECEIVER SR8002

(Using the unit)

In TUNER mode, press the T-MODEbutton on the remote controller to switch between AUTO STEREO and monaural sound.

1. Press the > button on the remote controller to display Page 2.

2. Each time the T-MODE (D3) button is pressed, the TUNER mode changes and the mode is displayed on the FL display.

Analog / Digital Auto Mode (Only on the SR8002)

T - M O D E : D I G - A T

For listening to HD Radio stations.

See p.70 for more information on HD Radio technology.

Note:

• This mode is not available on the SR7002.

Analog Auto Mode

(when receiving FM broadcasts)

T - M O D E : A N A - A T

AUTO STEREO mode is selected and the AUTO indicator is illuminated on the FL display.

When stereo broadcasts are received, the ST indicator is illuminated on the FL display.

Note:

•This mode is not available when BAND is set to AM.

•If the unit receives a weak signal or it is difficult to receive a stereo signal, press the T-MODEbutton on the remote controller or the unit to switch to MONO mode. This reduces the amount of noise and makes broadcasts easier to hear. The AUTO indicator on the FL display disappears.

SURROUND

DIGITAL

AAC

1. To select FM , press the BAND button on the front panel.

2. While pressing the MEMORY button, press the

1 cursor button.

“AUTO PRESET” will appear on the display, and scanning starts from the lowest frequency.

3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds.

During this time, the following operations are possible.

The band can be changed by the BAND button.

4. If no button is pressed during this period, the current station is memorized in location Preset 01.

If you wish to skip the current station, press the 3 cursor button during this period, this station is skipped and auto presetting continues.

5. Operation stops automatically when all 60 preset memory positions are fi lled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMORY button on the front panel. “– –“ (preset number) starts blinking on the display.

3. Select the preset number by pressing the 1 or 2 cursor buttons, while this is still blinking (approx. 5 seconds)

4. Press the MEMORY button again to enter. The display stops blinking.

The station is now stored in the specified preset memory location.

(Using the remote controller)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the remote controller. “– –“ (preset number) starts blinking on the display.

3. Enter the desired preset number by pressing the numeric buttons.

Note:

•When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.

68