Marantz SR7200 manual FM antenna terminal 75 ohms, AM antenna and ground terminals, PRE OUT jacks

Page 11

ENGLISH

REAR PANEL CONNECTIONS (SEE PAGE iii.)

All connections to the rear panel should be made with the entire system powered off.

To avoid errors, it is advisable to connect one cable at a time between the various components.

aFM antenna terminal (75 ohms)

Connect an external FM antenna with a coaxial cable, or a cable network FM source.

AM antenna and ground terminals

Connect the supplied AM loop antenna. Use the terminals marked “AM” and “GND”.

The supplied AM loop antenna will provide good AM reception in most areas.

Position the loop antenna until you hear the best reception.

sPRE OUT jacks

Jacks for Front - L/R, Center,Surround and Surround center. Use these jacks for connection to an external power amplifier.

dSUB WOOFER output jack

Connect to the input jack(s) of the power amplifier for subwoofer channel or powered subwoofer.

fDC control output 1 & 2

Connect a device that needs to be triggered by DC under certain conditions (screen, power strip, etc…) Use the system setup menu (3/ 3) to determine the conditions by which these jacks will be active.

Note:

This output voltage is for (status) control only, It is not sufficient for drive capability.

gMULTI OUT jacks (Audio)

Connect to the input jacks of the amplifier used to drive the speakers in another room (Second zone).

hAnalog audio outputs for audio source

equipment

TAPE and CD-R/MD

Connect each output to the audio inputs (REC in) of your recording equipment.

jAnalog audio inputs

CD, TAPE, and CD-R/MD

Connect the audio outputs of your source components to the input jacks on the receiver.

kVideo outputs

VCR1, and DSS/VCR2

Connect each output to the video input (REC in) of your video recording equipment.

lMULTI OUT jack (Video)

Connect to the input jack of the TV monitor in another room (Second zone).

¡0TV MONI. (VIDEO/S-VIDEO) output jacks

Connect the TV MONI jack to your TV’s video input (VIDEO IN) jack. You can connect your video equipment with S-VIDEO jacks if possible, or the composite VIDEO jacks.

You must use the same type of connection from your video player into the receiver, and out of the receiver into your TV.

Both must be composite video or both must be S-Video. You cannot convert a signal from one type to the other.

When you connect to S-video connections, there will be no signal output from the composite video jacks.

¡1COMPONENT VIDEO outputs

Connect to these outputs to the component video inputs of a video projector or monitor. When a source connected to one of the two component video inputs is selected the signal will be sent to these jacks.

¡2SPEAKER SYSTEMS A terminals

FRONT Left & Right speakers output terminals

Connect to the front left & right speakers.

CENTER speaker output terminals

Connect to the center speaker.

SURROUND Left & Right speakers output terminals

Connect to the surround (rear) left & right speakers.

SURROUND Center speakers output terminals

Connect to the surround center speakers.

¡3SPEAKER SYSTEMS B terminals

FRONT Left & Right speakers output terminals

Connect to the front left & right speakers.

Notes:

When you use the speaker systems A and B simultaneously, the connected speakers which are impeadance 12 to 16 ohms must be used.

¡47 CH INPUT jacks

Connect to the outputs of an external multichannel decoder.

¡5DIGITAL outputs

Optical and Coaxial

Connect digital input of your digital recording equipment.

¡6DIGITAL inputs

Dig.1,2 (Optical) and Dig. 3, 4, 5 (Coaxial)

Connect each input to the digital output of your source equipment. Use the system setup menu to assign digital input to appropriate source. (see page. 9)

Note :

The coaxial connections are not for AC-3 RF from the LD player, If you want to decode this type of signal, an external demodulator must be used.

¡7REMOTE CONT. IN/OUT terminals

Connect to a Marantz component equipped with remote control (RC- 5) terminals.

¡8MULTI ROOM REMOTE I/O terminals

IN : Connect to multi-room remote control device, available from

your Marantz dealer.

OUT : Connect to the Marantz component equipped with remote control (RC-5) terminals in another room (Second zone).

¡9Analog audio outputs for video source equipment

VCR1, and DSS/VCR2

Connect each output to the audio inputs (REC in) of your video recording equipment.

™0Analog audio inputs for video source equipment

TV, DVD, VCR1, and DSS/VCR2

Connect each input to the audio outputs of your video source equipment.

4

Image 11
Contents Model SR7200 User Guide Risk of Electric Shock Read Before Operating Equipment Important Safety InstructionsNEC Section Fg h j kl ¡0 ¡1 ¡2 ¡3 Video System Connections for Video Components FM Feeder FM External Antenna SUB WooferTable of Contents Description FeaturesIntroduction Video SUB Woofer output jack FM antenna terminal 75 ohmsAM antenna and ground terminals PRE OUT jacks3COMPONENT Video inputs 5Power cable1Video inputs 2S-video inputsConnection example Remote Control BUS Connections⁄7TEN Keypad Remote Control Unit RC7200SROn Screen Display Menu System SET-UPOSD Main Menu System SetupSystem Setup 2/3 Selecting the Digital Input System Setup 3/3 DC Control OutputSpkr Setup 3/3 Spkr Level Speakers SetupSpkr Setup 2/3 Spkr Distance Spkr Setup 1/3 Spkr SizeChannel Level Control Surround Mode Multi Room SetupPreset Tuning FM Mode Button OperationAuto Tuning Auto Tuning Using the Remote Control UnitNormal Playback Operation Using the SR7200Operation Using the remote unit Playback OperationMulti Room Selector Setting the Sleep TimerOther Functions TV Auto ON/OFF FunctionGeneral Information Fuction Select & Surround ModeMaster Volume Control On Screen Display InfomationOSD OFF Sleep TimerNames of Parts & Functions Main Features & Functions⁄1 3 CURSOR/ Transport Basic Operation Control indicatorUSE Mode Learn ModeIf Full is displayed on the LCD Programming the JOG DialErasing by Buttons Returning to Factory PresetsRewriting Names Erasing Programmed CodesErasing Code s by Function Erasing All Memory ContentsProgramming Macros Erasing Jog Dial CodesEditing Macros Using MacrosNow, execute the macro you just programmed Examples of Macro ProgramsClearing Macro Programs Number of Learnable Codes Battery LifeSetup Other FunctionsFor Rest setups JOG Dial Command Functions ListingFor USA setups Surround Surroud modeSurround Modes 1CHInput Signal Symptom Cause Remedy TroubleshootingGeneral Malfunction Memory backupFM Tuner Section Technical SpecificationsIs a registered trademark

SR7200 specifications

The Marantz SR7200 is a notable receiver that exemplifies high-quality audio performance coupled with advanced technology, making it a staple in home theater systems since its release. Designed for both music aficionados and home theater enthusiasts, the SR7200 offers a versatile array of features that enhance sound quality and user experience.

At the core of the SR7200 is a powerful amplification system, providing consumers with 110 watts per channel across seven channels. This ensures that users experience a robust and immersive sound, whether watching movies or listening to music. The receiver supports a wide range of surround sound formats, including Dolby Digital, Dolby Pro Logic II, DTS, and even virtual surround sound options, which allow for a powerful audio experience that fills the room.

One of the standout features of the Marantz SR7200 is its extensive connectivity options. The receiver is equipped with multiple HDMI inputs, allowing users to connect various sources such as Blu-ray players, gaming consoles, and streaming devices. Additionally, it has composite, component, and optical inputs, making it highly compatible with a multitude of devices. This wide array of inputs ensures that users can enjoy their favorite content without the hassle of switching cables.

The SR7200 also boasts advanced room calibration technology, which helps optimize audio performance according to the unique acoustics of the listening environment. Through the use of microprocessors, the receiver automatically adjusts speaker levels, equalization, and timing to ensure the best possible sound quality, regardless of room layout. This feature is particularly beneficial for novice users who may not have extensive knowledge of audio setup.

In terms of build quality, the Marantz SR7200 is constructed with attention to detail, featuring a solid chassis that is designed to minimize interference and reduce vibrations. The tonal balance is excellent, with crisp highs and deep, rich lows that enhance any audio playback.

Moreover, the receiver is user-friendly, with a nicely designed remote control and an intuitive on-screen setup process, making it accessible for everyone from beginners to seasoned audiophiles.

In summary, the Marantz SR7200 is a feature-rich A/V receiver that combines powerful amplification, multiple connectivity options, advanced audio processing technologies, and user-focused design. It remains a compelling choice for anyone seeking to enhance their home audio experience.