Jonsered CS 2171, CS2163, CS 2165 manual Air filter, Muffler, Needle bearing maintenance, Spark plug

Page 31

MAINTENANCE

Air filter

The air filter must be regularly cleaned from dust and dirt in order to avoid:

•Carburetor malfunctions

• Starting problems

• Engine power reduction

• Unnecessary wear on the engine parts

• Abnormal fuel consumption

Clean the air filter daily or more often if the air is exceptionally dusty in the working area.

•Disassemble the air filter by

removing the air filter-cover and unscrew the filter. When reassembling, make sure that the filter is tight against the filter holder. Clean the filter by brushing or shaking it.

Muffler

The muffler is designed in order to reduce the noise level

and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material. Some mufflers are equipped with a special screen.

If your saw has this type of muffler, you should clean the screen at least once a week. This is done with a wire brush.

CAUTION! The screen must be replaced, if damaged. The saw will be overheated, if the screen is clogged. This results in damage on the cylinder and the piston. Never use a saw with a clogged or defective muffler.

Needle bearing maintenance

•A more thorough cleaning of the filter is obtained by washing it in water and soap.

An air filter, which is used for some time, cannot be cleaned completely. Therefore it must be replaced by a new one, with regular intervals.

IMPORTANT! A damaged air filter must always be replaced.

Spark plug

The spark plug condition is influenced by:

The clutch drum is equipped with one of the following chain sprockets:

•Spur sprocket (A) (the chain sprocket is welded on the drum)

•Rim sprocket (B) (exchangeable)

Both versions have built-in needle bearing at the drive shaft, whitch has to be greased regularly (once a week).

NOTE! Use only high quality bearing grease or engine oil.

A

B

•An incorrect carburetor setting.

•Wrong fuel mixture (too much oil in the gasoline).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in malfunction and starting difficulties.

If the engine is low on

0,5 mm

power, difficult to start or

 

runs poorly at idling speed,

 

always check the spark plug

 

first. If the spark plug is dirty,

 

clean it and check the

 

electrode gap. Readjust if

 

necessary. The correct gap is

 

0.5mm (.020"). The spark plug should be replaced after about a month in operation or earlier if the electrodes are

badly eroded.

IMPORTANT! Always use the recommended spark plug type. An incorrect spark plug can severely damage the piston/cylinder.

Adjustment of the oil pump

The oil pump is adjustable. Ad- justments are made by turning the screw using a screwdriver or combination spanner. The saw is supplied from the factory set to 1 turn open. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.

!WARNING! The engine must not be running when making adjustments.

Recommended settings:

Bar -15": 1 turns from the closed position.

Bar 15"-18": 2 turns from the closed position.

Bar 18"-24": 3 turns from the closed position.

Bar 24"- : 4 turns from the closed position.

These recommendations apply to Jonsered’s chain oil, for other chain oil increase the oil flow by one step.

English – 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents EPA Symbols KEY to SymbolsEPA ContentsPersonal Protective Equipment Safety Instructions3a Starting Chain brake and front hand guardChain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainRisk of kickback is increased with a badly sharpened chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Sharpening cutting teethSetting the raker clearance General advice on setting raker clearanceTensioning the chain Never use waste oil Lubricating cutting equipmentChain oil Filling with chain oilChain drive sprocket Checking chain lubrication Needle bearing maintenanceChecking wear on cutting equipment Lubricating the bar tip sprocketWhat is kickback? HOW to Avoid KickbackDo not let go of the handles General rulesNever use the saw one- handed 10 ft Min mGeneral Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatFreeing a Trapped tree General adviceFreeing a tree that has fallen badly = high accident risk Cutting the trunk into logsWhat is what? What is WHAT?Mounting guide bar and chain AssemblyFuelmix Fuel HandlingChain oil Min 3 m Fuelling10ft Stop Start and StopStart and stop StartCarburetor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordMuffler Needle bearing maintenanceAdjustment of the oil pump Air filterWinter use Centrifugal cleaning TurboCooling system Heated handles CS 2163 W/CS 2171 WMonthly maintenance Weekly maintenance Daily maintenanceTechnical Data + 46 36 14 65 00. Warranty Period Emission Control Warranty Statement+ 46 36 14 65 2002W39 108 88

CS 2165, CS 2171, CS2163 specifications

The Jonsered CS2163, CS2171, and CS2165 are a trio of powerful chain saws designed for professionals and serious enthusiasts alike. These models are particularly noteworthy for their blend of performance, durability, and user-friendly features, making them suitable for a wide range of cutting tasks.

The Jonsered CS2163 is equipped with a robust 3.1 kW engine, providing ample power for various cutting jobs, from felling trees to limbing and even cutting firewood. One of its notable features is the Quick-Release Air Filter, which allows for easy access and maintenance, ensuring optimal engine performance. Additionally, the CS2163 incorporates the Smart Start technology that reduces the resistance in the starter cord, allowing users to start the saw with minimal effort.

The CS2171, on the other hand, is a more advanced model designed for heavy-duty applications. This saw comes with a 3.4 kW engine and boasts a larger cutting capacity, making it perfect for professional users who tackle more demanding tasks. Its X-Torq engine design significantly lowers fuel consumption and emissions, aligning with environmental standards while delivering exceptional power. The CS2171 also features an anti-vibration system that enhances user comfort during extended cutting sessions, therefore maximizing productivity without sacrificing ease of use.

The CS2165 occupies a sweet spot between the CS2163 and CS2171, offering a balance of power and efficiency. Powered by a 3.2 kW engine, it provides ample performance for most tasks while still being lightweight for easy maneuverability. This model includes the same Quick-Release Air Filter found in the CS2163, making maintenance a breeze. The CS2165 also features an adjustable oil pump, allowing users to customize the oil flow to the chain based on their specific cutting needs, enhancing the longevity of both the saw and the chain.

All three models prioritize user safety, featuring a chain brake system that quickly halts the chain in case of kickback. Furthermore, the ergonomic design of the handles offers a comfortable grip, reducing fatigue during longer cutting sessions.

In summary, the Jonsered CS2163, CS2171, and CS2165 are exceptional chainsaws that cater to the needs of professionals and enthusiasts alike, combining power, technology, and ease of use in one reliable package. Their innovative features, efficient engines, and focus on user comfort make them an excellent choice for anyone in need of a high-performance chainsaw.
Top Page Image Contents