Jonsered CS2163, CS 2171 manual Changing a broken or worn starter cord, Starter device assembly

Page 30

MAINTENANCE

Starter device

!WARNING!

•When the recoil spring is assembled in the starter housing, it is in tensioned position and can when treated carelessly, pop out and cause injuries.

•Always be careful, when changing the recoil spring or the starter cord. Always wear safety goggles for eye protection.

Changing a broken or worn starter cord

• Loosen the screws, that hold the starter device against the crankcase and remove the starter device.

•Pull out the cord approx. 30 cm and lift it up into the notch in the pulley. Zero-set the recoil spring by letting

the pulley rotate slowly backwards. Undo the screw in the centre of the pulley and remove the pulley.

•Insert and fasten a new starter cord in the pulley. Wind approx. 3 turns of the starter cord on to the pulley. Assemble the starter pulley

against the recoil spring, so the end of the spring engages to the pulley. Fit the screw in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Make a knot on the starter cord.

Tensioning the recoil spring

•Lift the starter cord up in the notch on the starter pulley and turn the starter pulley 2 turns clockwise.

NOTE! Check that the starter pulley can be turned at least half a turn, when the starter cord is entirely pulled out.

Changing the broken recoil spring

•Lift the starter pulley. (See, Changing a broken or worn

starter cord). The recoil spring is mounted inside the starter pully. Dissasemble the recoil spring by tapping the pully (with its inside facing down) lightly against a working bench or similar.

• Put a new recoil spring in the right position. If the spring pops out when assembling, it should be mounted again, out and in towards the centre.

•Lubricate the recoil spring with thin oil. Assemble the starter pulley, and tension the recoil spring.

Starter device assembly

•Assemble the starter device, by pulling the starter cord out first, then place the starter against the

crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

• Assemble and tighten the screws, which hold the starter.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents EPA KEY to Symbols SymbolsContents EPASafety Instructions Personal Protective EquipmentChain brake and front hand guard 3a StartingThrottle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the inertia brake release Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainSharpening cutting teeth Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Risk of kickback is increased with a badly sharpened chainGeneral advice on setting raker clearance Setting the raker clearanceTensioning the chain Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilLubricating the bar tip sprocket Checking chain lubrication Needle bearing maintenanceChecking wear on cutting equipment Chain drive sprocketHOW to Avoid Kickback What is kickback?General rules Do not let go of the handlesNever use the saw one- handed Min m 10 ftBasic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? What is what?Assembly Mounting guide bar and chainFuel Handling FuelmixChain oil Fuelling Min 3 m10ft Start Start and StopStart and stop StopMaintenance CarburetorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springAir filter Needle bearing maintenanceAdjustment of the oil pump MufflerHeated handles CS 2163 W/CS 2171 W Centrifugal cleaning TurboCooling system Winter useWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data Emission Control Warranty Statement + 46 36 14 65 00. Warranty Period+ 46 36 14 65 108 88 2002W39

CS 2165, CS 2171, CS2163 specifications

The Jonsered CS2163, CS2171, and CS2165 are a trio of powerful chain saws designed for professionals and serious enthusiasts alike. These models are particularly noteworthy for their blend of performance, durability, and user-friendly features, making them suitable for a wide range of cutting tasks.

The Jonsered CS2163 is equipped with a robust 3.1 kW engine, providing ample power for various cutting jobs, from felling trees to limbing and even cutting firewood. One of its notable features is the Quick-Release Air Filter, which allows for easy access and maintenance, ensuring optimal engine performance. Additionally, the CS2163 incorporates the Smart Start technology that reduces the resistance in the starter cord, allowing users to start the saw with minimal effort.

The CS2171, on the other hand, is a more advanced model designed for heavy-duty applications. This saw comes with a 3.4 kW engine and boasts a larger cutting capacity, making it perfect for professional users who tackle more demanding tasks. Its X-Torq engine design significantly lowers fuel consumption and emissions, aligning with environmental standards while delivering exceptional power. The CS2171 also features an anti-vibration system that enhances user comfort during extended cutting sessions, therefore maximizing productivity without sacrificing ease of use.

The CS2165 occupies a sweet spot between the CS2163 and CS2171, offering a balance of power and efficiency. Powered by a 3.2 kW engine, it provides ample performance for most tasks while still being lightweight for easy maneuverability. This model includes the same Quick-Release Air Filter found in the CS2163, making maintenance a breeze. The CS2165 also features an adjustable oil pump, allowing users to customize the oil flow to the chain based on their specific cutting needs, enhancing the longevity of both the saw and the chain.

All three models prioritize user safety, featuring a chain brake system that quickly halts the chain in case of kickback. Furthermore, the ergonomic design of the handles offers a comfortable grip, reducing fatigue during longer cutting sessions.

In summary, the Jonsered CS2163, CS2171, and CS2165 are exceptional chainsaws that cater to the needs of professionals and enthusiasts alike, combining power, technology, and ease of use in one reliable package. Their innovative features, efficient engines, and focus on user comfort make them an excellent choice for anyone in need of a high-performance chainsaw.
Top Page Image Contents