Jonsered CS 2165, CS2163 Emission Control Warranty Statement, + 46 36 14 65 00. Warranty Period

Page 35

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND

OBLIGATIONS

The EPA (The US Environmental Protection Agency) and Jonsered are pleased to explain the emissions control system warranty on your 2000 and later small nonroad engine. In U.S. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards.

Jonsered must warrant the emission control system on your small nonroad engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your unit. Your emission control system includes Parts such as the carburetor and the ignition system. Where a warrantable condition exists, Jonsered will repair your small nonroad engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE

The 2000 and later small nonroad engines are warranted for two years. If any emission related part on your engine (as listed above) is defective, the part will be repaired or replaced by Jonsered.

OWNER’S WARRANTY RESPONSIBILITIES

As the small nonroad engine owner, you are responsible for the performance of the required maintenance listed in your Operator’s Manual. Jonsered recommends that you retain all receipts covering maintenance on your small nonroad engine, but Jonsered cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the small nonroad engine owner, you should, however, be aware that Jonsered may deny you warranty coverage if your small nonroad engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications or the use of parts not made or approved by the original equipment manufacturer.

You are responsible for presenting your small nonroad engine to a Jonsered authorized servicing dealer as soon as a problem exists.

The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered, at Sweden + 46 36 14 65 00.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small nonroad engine is delivered.

LENGTH OF COVERAGE

Jonsered warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Jonsered servicing dealer. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered at Sweden

+46 36 14 65 00. WARRANTY PERIOD

Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of ”repair or replace as necessary” shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part.

DIAGNOSIS

The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an approved Jonsered servicing dealer.

CONSEQUENTIAL DAMAGES

Jonsered may be liable for damages to other engine components caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD -ON OR MODIFIED PARTS

The use of add-on or modified parts can be grounds for disallowing a warranty claim. Jonsered is not liable to cover failures of warranted parts caused by the use of add-on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Jonsered at Sweden

+ 46 36 14 65 00.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all Jonsered authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Any Jonsered approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS LIST

1.Carburetor and internal parts

2.Intake pipe, airfilter holder and carburetor bolts.

3.Airfilter and fuelfilter covered up to maintainance schedule.

4.Ignition System

a)Spark Plug, covered up to maintenance schedule

b)Ignition Module

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required maintenance, as defined in the operator’s manual.

English – 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents EPA Symbols KEY to SymbolsEPA ContentsPersonal Protective Equipment Safety Instructions3a Starting Chain brake and front hand guardRight hand guard Throttle lockChain catcher Muffler Stop switchVibration damping system Checking the brake trigger Checking brake band wearChecking the front hand guard Checking the inertia brake releaseThrottle lock 5 basic rules Cutting EquipmentSome terms that describe the bar and chain Cutting equipment designed to minimise kickbackBar Saw chainRisk of kickback is increased with a badly sharpened chain Sharpening your chain and adjusting raker clearanceGeneral information on sharpening cutting teeth Sharpening cutting teethTensioning the chain General advice on setting raker clearanceSetting the raker clearance Never use waste oil Lubricating cutting equipmentChain oil Filling with chain oilChain drive sprocket Checking chain lubrication Needle bearing maintenanceChecking wear on cutting equipment Lubricating the bar tip sprocketWhat is kickback? HOW to Avoid KickbackNever use the saw one- handed General rulesDo not let go of the handles 10 ft Min mGeneral Working Instructions Basic safety rulesCutting Basic cutting techniqueGeneral TermsFelling direction Tree felling techniqueSafe distance LimbingFelling Clearing the trunk and preparing your retreatFreeing a Trapped tree General adviceFreeing a tree that has fallen badly = high accident risk Cutting the trunk into logsWhat is what? What is WHAT?Mounting guide bar and chain AssemblyChain oil Fuel HandlingFuelmix 10ft FuellingMin 3 m Stop Start and StopStart and stop StartCarburetor MaintenanceTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordMuffler Needle bearing maintenanceAdjustment of the oil pump Air filterWinter use Centrifugal cleaning TurboCooling system Heated handles CS 2163 W/CS 2171 WMonthly maintenance Weekly maintenance Daily maintenanceTechnical Data + 46 36 14 65 Emission Control Warranty Statement+ 46 36 14 65 00. Warranty Period 2002W39 108 88

CS 2165, CS 2171, CS2163 specifications

The Jonsered CS2163, CS2171, and CS2165 are a trio of powerful chain saws designed for professionals and serious enthusiasts alike. These models are particularly noteworthy for their blend of performance, durability, and user-friendly features, making them suitable for a wide range of cutting tasks.

The Jonsered CS2163 is equipped with a robust 3.1 kW engine, providing ample power for various cutting jobs, from felling trees to limbing and even cutting firewood. One of its notable features is the Quick-Release Air Filter, which allows for easy access and maintenance, ensuring optimal engine performance. Additionally, the CS2163 incorporates the Smart Start technology that reduces the resistance in the starter cord, allowing users to start the saw with minimal effort.

The CS2171, on the other hand, is a more advanced model designed for heavy-duty applications. This saw comes with a 3.4 kW engine and boasts a larger cutting capacity, making it perfect for professional users who tackle more demanding tasks. Its X-Torq engine design significantly lowers fuel consumption and emissions, aligning with environmental standards while delivering exceptional power. The CS2171 also features an anti-vibration system that enhances user comfort during extended cutting sessions, therefore maximizing productivity without sacrificing ease of use.

The CS2165 occupies a sweet spot between the CS2163 and CS2171, offering a balance of power and efficiency. Powered by a 3.2 kW engine, it provides ample performance for most tasks while still being lightweight for easy maneuverability. This model includes the same Quick-Release Air Filter found in the CS2163, making maintenance a breeze. The CS2165 also features an adjustable oil pump, allowing users to customize the oil flow to the chain based on their specific cutting needs, enhancing the longevity of both the saw and the chain.

All three models prioritize user safety, featuring a chain brake system that quickly halts the chain in case of kickback. Furthermore, the ergonomic design of the handles offers a comfortable grip, reducing fatigue during longer cutting sessions.

In summary, the Jonsered CS2163, CS2171, and CS2165 are exceptional chainsaws that cater to the needs of professionals and enthusiasts alike, combining power, technology, and ease of use in one reliable package. Their innovative features, efficient engines, and focus on user comfort make them an excellent choice for anyone in need of a high-performance chainsaw.
Top Page Image Contents