Jonsered manual Low speed jet L, Fine adjustment of the idle speed T, High speed jet H RS52

Page 26

MAINTENANCE

Low speed jet L

Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/ 4 turn counter-clockwise.

+ 1/4

L

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate.

WARNING! If the idle speed cannot be

!adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

High speed jet H (GR41, GR50, RS44)

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly.

H

Note that the engine should not be under load when you adjust the high speed jet H. You should therefore remove the cutting attachment, nut, support flange and drive disc before adjusting the high speed jet H.

The high speed jet H is adjusted correctly when the machine burbles a little. If the machine races then the setting is too lean. If the engine produces a lot of smoke and burbles a lot then the setting is too rich.

CAUTION! For optimum adjustment of the carburettor, contact a qualified dealer/service workshop that has a revolution counter at their disposal.

High speed jet H (RS52)

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

Setting procedure without a load (Blade can be used)

The machine is equipped with speed control in the ignition system. It is extremely important to be aware of this when adjusting the carburettor.

RS52: Speed control at: 13500 rpm

When attempting to adjust the speed over that specified, the speed is not changed, but only causes the engine to receive too little fuel resulting in a large risk of engine failure.

Run the machine warm for approximately 5 minutes alternating between short intervals of full throttle and idling. When the carburettor is to be adjusted, apply full throttle and turn the H-needle anti-clockwise until the engine speed reaches 10,500-11,000 r/min (burbles) or until the cap reaches its stop position. Now turn the H-needle slowly clockwise until the engine reaches the speed when the speed control comes into force. In some cases, speed control can come into force at 200-300 revs below or above that specified. It is important that you do not continue to turn the H-needle clockwise when the engine speed has stabilised. Screw the H-needle (anti-clockwise) a few tenths of a turn instead.

H

Setting procedure with a load (Trimmer head should be used)

Ensure the length of the trimmer cord is correct, i.e. exactly reaches the knife on the trimmer guard. Use either 3 mm or 3.3 mm diameter trimmer cord.

Run the machine warm for about 5 minutes mostly at full throttle. When the carburettor is to be adjusted, apply full throttle and turn the H-needle anti-clockwise until the engine burbles or until the cap reaches its stop position. (If the engine runs smoothly when the cap is in its stop position no further adjustment is necessary!) Turn the H-needle slowly clockwise until the engine runs absolutely smoothly. (Burbling has stopped completely). Now screw the H-needle (anti- clockwise) a few tenths of a turn.

H

CAUTION! For optimum adjustment of the carburettor, contact a qualified dealer/service workshop that has a revolution counter at their disposal.

26 – English

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Operator’s manual EPA KEY to Symbols SymbolsContents Introduction Dear customerWhat is WHAT? What is what on the clearing saw? RS44What is what on the clearing saw? RS52 General Safety Precautions Personal protective equipmentThrottle lockout Machine′s safety equipmentStop switch Quick release Cutting attachment guardVibration damping system MufflerLocking nut Locking screwCutting equipment Cutting equipmentTrimmer head Sharpening grass cutters and grass bladesSharpening the saw blade Transport position, handlebar AssemblyAssembling the handlebar and throttle Assembling the cutting equipmentFitting the blade guard and saw blade Fitting the trimmer guard and trimmer head Trimmy SIIStandard harness Adjusting the harness and clearing sawFitting other guards and cutting attachments Correct balance Adjusting the harnessVector harness Fuel Fuel safetyFuel Handling Fueling MixingStarting and stopping Starting and StoppingCheck before starting Cold engineStarting StoppingGeneral working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Working methodsGrass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingMaintenance CarburetorHigh speed jet H GR41, GR50, RS44 Fine adjustment of the idle speed TLow speed jet L High speed jet H RS52Muffler Correctly adjusted carburetorCleaning the air filter Cooling systemBevel gear Spark plugMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsTrimmy SII Page ´z+R¶5Q¨ Page 1150269-95 ´z+R¶5Q¨ ´z+R¶5Q¨

RS52 specifications

The Jonsered RS52 is a robust and high-performance chainsaw renowned for its blend of power and user-friendly design, making it an ideal choice for both professional lumberjacks and serious DIY enthusiasts. This versatile tool is engineered to tackle a range of forestry tasks, from felling trees to trimming branches and preparing firewood.

One of the main features of the RS52 is its powerful engine. The chainsaw is equipped with a 52cc two-stroke engine that delivers impressive performance, enabling it to handle larger logs with ease. This power ensures efficiency and speed during cutting operations, allowing users to complete their tasks in less time. Despite its powerful engine, the RS52 is designed to minimize fuel consumption, making it an eco-friendly option for users who are conscious about their environmental impact.

In terms of technology, the Jonsered RS52 boasts a well-designed air injection system that helps to keep the air filter cleaner for longer durations. This innovation not only extends the life of the filter but also maintains engine performance by ensuring a steady supply of clean air. Additionally, this chainsaw features an easy start mechanism, reducing the effort needed to start the engine and making it user-friendly for individuals of all skill levels.

Safety is a paramount consideration in the design of the RS52. The chainsaw incorporates a chain brake system that allows for quick stopping in the event of kickback, significantly enhancing user safety. Furthermore, the ergonomic design of the handle promotes comfort during use, reducing fatigue even during prolonged cutting sessions.

The RS52 is equipped with a durable chain and bar, designed for optimal cutting performance and longevity. The chain tensioning system allows for straightforward adjustments, ensuring that the chain remains taut and functioning properly.

Overall, the Jonsered RS52 chainsaw is a powerful and efficient tool that combines advanced technology with user-centric features. Its robust performance, safety mechanisms, and ease of use make it a preferred choice for professionals and hobbyists alike, proving its worth in various cutting tasks. Whether you are a seasoned professional or a weekend woodworker, the RS52 is engineered to deliver reliability and exceptional results in every operation.
Top Page Image Contents