Jonsered RS52 manual Maintenance schedule, Maintenance Daily Weekly Monthly

Page 29

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop.

Maintenance

Daily

Weekly

Monthly

maintenance

maintenance

maintenance

 

 

 

 

 

Clean the outside of the machine.

X

 

 

 

 

 

 

Check that the harness is not damaged.

X

 

 

 

 

 

 

Make sure the throttle trigger lock and the throttle function correctly from a

X

 

 

safety point of view.

 

 

 

 

 

 

 

 

 

Check that the handle and handlebar are undamaged and secured

X

 

 

correctly.

 

 

 

 

 

 

 

 

 

Check that the stop switch works correctly.

X

 

 

 

 

 

 

Check that the cutting attachment does not rotate at idle.

X

 

 

 

 

 

 

Clean the air filter. Replace if necessary.

X

 

 

 

 

 

 

Check that the guard is undamaged and not cracked. Replace the guard if

X

 

 

it has been exposed to impact or is cracked.

 

 

 

 

 

 

 

 

 

Check that the blade is correctly centred, is sharp, and is not cracked. An

 

 

 

off-centre blade will cause vibration that could result in damage to the

X

 

 

machine.

 

 

 

 

 

 

 

Check that the trimmer head is undamaged and not cracked. Replace the

X

 

 

trimmer head if necessary.

 

 

 

 

 

 

 

 

 

Check that the locking nut of the cutting equipment is tighten correctly.

X

 

 

 

 

 

 

Check that the locking screw is tightened when using a support cup with

X

 

 

bearings.

 

 

 

 

 

 

 

 

 

Check that the transport guard for the blade is intact and that it can be

X

 

 

secured correctly.

 

 

 

 

 

 

 

 

 

Check that nuts and screws are tight.

X

 

 

 

 

 

 

Check that there are no fuel leaks from the engine, tank or fuel lines.

X

 

 

 

 

 

 

Check the starter and starter cord.

 

X

 

 

 

 

 

Check that the vibration damping elements are not damaged.

 

X

 

 

 

 

 

Clean the outside of the spark plug. Remove it and check the electrode

 

 

 

gap. Adjust the gap to 0.5 mm (.20”), or replace the spark plug. Check that

 

X

 

the spark plug is fitted with a suppressor.

 

 

 

 

 

 

 

Clean the machines cooling system.

 

X

 

 

 

 

 

Clean or replace the spark arrestor screen on the muffler (only applies to

 

X

 

mufflers without a catalytic converter).

 

 

 

 

 

 

 

 

 

Clean the outside of the carburettor and the space around it.

 

X

 

 

 

 

 

Check that the bevel gear is filled three-quarters full with lubricant. Fill if

 

X

 

necessary using special grease.

 

 

 

 

 

 

 

 

 

Check the fuel filter from contamination and the fuel hose from cracks or

 

 

X

other defects. Replace if necessary.

 

 

 

 

 

 

 

 

 

Check all cables and connections.

 

 

X

 

 

 

 

Check the clutch, clutch springs and the clutch drum for wear. Replace if

 

 

X

necessary by an autorized service workshop.

 

 

 

 

 

 

 

 

 

Replace the spark plug. Check that the spark plug is fitted with a

 

 

X

suppressor.

 

 

 

 

 

 

 

 

 

Check and clean the spark arrestor screen on the muffler (only applies to

 

 

X

mufflers fitted with a catalytic converter).

 

 

 

 

 

 

 

 

 

RS52: Lubricate the drive shaft with the special grease.

Do this every three months.

 

 

 

 

 

English – 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Operator’s manual EPA Symbols KEY to SymbolsContents Dear customer IntroductionWhat is what on the clearing saw? RS44 What is WHAT?What is what on the clearing saw? RS52 Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipmentStop switch Vibration damping system Cutting attachment guardQuick release MufflerLocking screw Locking nutCutting equipment Cutting equipmentTrimmer head Sharpening grass cutters and grass bladesSharpening the saw blade Assembling the handlebar and throttle AssemblyTransport position, handlebar Assembling the cutting equipmentFitting the trimmer guard and trimmer head Trimmy SII Fitting the blade guard and saw bladeStandard harness Adjusting the harness and clearing sawFitting other guards and cutting attachments Correct balance Adjusting the harnessVector harness Fuel Fuel safetyFuel Handling Mixing FuelingCheck before starting Starting and StoppingStarting and stopping Cold engineStopping StartingWorking Techniques Basic safety rulesGeneral working instructions ABC of clearingWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeTrimming Grass trimming with a trimmer headCarburetor MaintenanceLow speed jet L Fine adjustment of the idle speed THigh speed jet H GR41, GR50, RS44 High speed jet H RS52Cleaning the air filter Correctly adjusted carburetorMuffler Cooling systemSpark plug Bevel gearMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataYour Warranty Rights and Obligations Federal Emission Control Warranty StatementTrimmy SII Page ´z+R¶5Q¨ Page 1150269-95 ´z+R¶5Q¨ ´z+R¶5Q¨

RS52 specifications

The Jonsered RS52 is a robust and high-performance chainsaw renowned for its blend of power and user-friendly design, making it an ideal choice for both professional lumberjacks and serious DIY enthusiasts. This versatile tool is engineered to tackle a range of forestry tasks, from felling trees to trimming branches and preparing firewood.

One of the main features of the RS52 is its powerful engine. The chainsaw is equipped with a 52cc two-stroke engine that delivers impressive performance, enabling it to handle larger logs with ease. This power ensures efficiency and speed during cutting operations, allowing users to complete their tasks in less time. Despite its powerful engine, the RS52 is designed to minimize fuel consumption, making it an eco-friendly option for users who are conscious about their environmental impact.

In terms of technology, the Jonsered RS52 boasts a well-designed air injection system that helps to keep the air filter cleaner for longer durations. This innovation not only extends the life of the filter but also maintains engine performance by ensuring a steady supply of clean air. Additionally, this chainsaw features an easy start mechanism, reducing the effort needed to start the engine and making it user-friendly for individuals of all skill levels.

Safety is a paramount consideration in the design of the RS52. The chainsaw incorporates a chain brake system that allows for quick stopping in the event of kickback, significantly enhancing user safety. Furthermore, the ergonomic design of the handle promotes comfort during use, reducing fatigue even during prolonged cutting sessions.

The RS52 is equipped with a durable chain and bar, designed for optimal cutting performance and longevity. The chain tensioning system allows for straightforward adjustments, ensuring that the chain remains taut and functioning properly.

Overall, the Jonsered RS52 chainsaw is a powerful and efficient tool that combines advanced technology with user-centric features. Its robust performance, safety mechanisms, and ease of use make it a preferred choice for professionals and hobbyists alike, proving its worth in various cutting tasks. Whether you are a seasoned professional or a weekend woodworker, the RS52 is engineered to deliver reliability and exceptional results in every operation.
Top Page Image Contents