Jonsered CS 2171WH manual Cutting equipment, General rules, Muffler, Bar

Page 9

SAFETY INSTRUCTIONS

Muffler

Never use a machine that has a faulty muffler.

Regularly check that the muffler is securely attached to the machine.

If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage.

Never use a muffler if the spark arrestor mesh is missing or defective.

WARNING! Never use a machine with faulty

!safety equipment. The machine’s safety equipment must be checked and maintained as described in this section. If your machine fails any of these checks contact your service agent to get it repaired.

Cutting equipment

This section describes how to choose and maintain your cutting equipment in order to:

Reduce the risk of kickback.

Reduce the risk of the chain breaking or jumping.

Obtain maximum cutting performance.

Extend the life of cutting equipment.

General rules

Only use cutting equipment recommended by us! See the Technical data section.

Keep the chain’s cutting teeth properly sharpened! Follow our instructions and use the recommended file gauge. A damaged or badly sharpened chain increases the risk of accidents.

Maintain the correct raker clearance! Follow our instructions and use the recommended raker gauge. Too large a clearance increases the risk of kickback.

Keep the chain properly tensioned! If the chain is slack it is more likely to jump off and lead to increased wear on the bar, chain and drive sprocket.

Keep cutting equipment well lubricated and properly maintained! A poorly lubricated chain is more likely to break and lead to increased wear on the bar, chain and drive sprocket.

Cutting equipment designed to minimise kickback

WARNING! Faulty cutting equipment or the

!wrong combination of bar and chain increases the risk of kickback! Use only the bar and chain combinations that we recommend. See the Technical data section.

The only way to avoid kickback is to make sure that the kickback zone of the bar never touches anything.

By using cutting equipment with ”built-in” kickback reduction and keeping the chain sharp and well-maintained you can reduce the effects of kickback.

Bar

The smaller the tip radius the smaller the kickback zone and the lower the chance of kickback.

English – 9

Image 9
Contents Operator´s manual Key to symbols KEY to SymbolsContents Safety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardChecking brake band wear MufflerChecking the front hand guard Checking the inertia brake releaseThrottle lock Stop switchChain catcher Right hand guardGeneral rules Cutting equipmentCutting equipment designed to minimise kickback MufflerChain Sharpening your chain and adjusting raker clearanceSome terms that describe the bar and chain General information on sharpening cutting teethSharpening cutting teeth Setting the raker clearance General advice on setting raker clearanceTensioning the chain If the raker clearance is too largeLubricating cutting equipment What is kickback? How to avoid kickbackChecking wear on cutting equipment Chain drive sprocketDo not let go of the handles Starting General safety precautionsBasic safety rules Fuel safetyGeneral working instructions Transport and storageBasic cutting technique GeneralTerms Limbing CuttingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Cutting the trunk into logsFreeing a tree that has fallen badly General adviceFreeing a trapped tree Cutting trees and branches that are in tensionWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingPetrol Two-stroke oilChain oil FuellingMin 3 m 10ft Starting and stopping Starting and StoppingCold engine Warm engineStopping Maintenance Carburettor adjustmentCarburettor with movement limiters Correctly adjusted carburettor Fine adjustment of the idle speed TCarburettor without movement limiters Low speed jet LIdle speed, rpm Recommended engine speeds are as followsAir filter StarterWhen making adjustments Adjustment of the oil pumpSpark plug MufflerCooling system Centrifugal cleaning TurboHeated handles Electrical carburettor heatingDaily maintenance Weekly maintenance Monthly maintenanceBelow you will find some general maintenance instructions Technical data Technical DataBar and chain combinations Bar ChainLength, inches Pitch, inch Max. number of teeth on EC-declaration of conformity Applies to Europe onlyEN292-2, Cispr 121997, EN608 Page 1088935-26 ´z*xT¶6U¨ ´z*xT¶6U¨