Jonsered 2149 manual What Is What?, What is what?

Page 24

WHAT IS WHAT?

	L	H
		T
H
Jonsered 2149W TURBO
XXXX
XXXXXXX
Husqvarna AB
Huskvarna, SWEDEN
J O N S E R E D S E R V I C E
Jonsered Power Products AB	108 07 01-08
433 81 Partille Sweden

What is what?

1.Cylinder cover.

2.Front handle.

3.Front hand guard.

4.Starter cover.

5.Chain oil tank.

6.Starter handle.

7.Adjuster screw, carburetor.

8.Choke control/Start throttle lock.

9.Rear handle.

10.Stop switch. Ignition on/off switch.

11.Fuel tank.

12.Muffler.

13.Bar tip sprocket.

14.Saw chain.

15.Saw bar.

16.Bumper.

17.Chain catcher. Catches chain if it jumps or breaks.

18.Clutch cover.

19.Right hand guard. Protects right hand if chain breaks or jumps.

20.Throttle control.

21.Throttle lock. Prevents accidental operation of throttle control.

22.Decompression valve.

23.Combination spanner.

24.Chain tensioning screw.

25.Operator´s manual.

26.Bar guard.

27.Oil pump adjustment screw.

28.Switch for heated handles (2149W).

24 – English

Image 24

Contents Operator´s manual KEY TO SYMBOLS SymbolsCONTENTS ContentsBefore using a new saw Safety instructionsSAFETY INSTRUCTIONS CHAIN SAW SAFETY EQUIPMENTPERSONAL PROTECTIVE EQUIPMENT 1 Chain brake and front hand guard 2 Throttle lock 3 Chain catcher4 Right hand guard 6 Stop switch 5 Vibration damping system7 Muffler 1Checking brake band wear 2 Checking the front hand guard3 Checking the inertia brake release 4Checking the brake triggerSAFETY INSTRUCTIONS CUTTING EQUIPMENT The 5 basic rules1Cutting equipment designed to minimise kickback A BarB Saw chain C Some terms that describe the bar and chainAGeneral information on sharpening cutting teeth B Sharpening cutting teethC General advice on setting raker clearance DSetting the raker clearance3 Tensioning the chain 4 Lubricating cutting equipment A Chain oilBFilling with chain oil E Needle bearing maintenance C Checking chain lubricationFChecking wear on cutting equipment D Lubricating the bar tip sprocketHOW TO AVOID KICKBACK What is kickback?H Bar General rules Do not let go of the handlesNever use the saw one- handed GENERAL SAFETY PRECAUTIONS ”Technical data” section”Maintenance” Min. 3 m1 Basic safety rules GENERAL WORKING INSTRUCTIONS2 Basic cutting technique GeneralTerms Cutting3 Tree felling technique A Safe distanceLimbing B Felling directionC Clearing the trunk and preparing your retreat D FellingDIRECTIONAL CUT FELLING CUTE Limbing F Cutting the trunk into logsAFreeing a “Trapped tree” WHAT IS WHAT? What is what?ASSEMBLY Mounting guide bar and chainFUEL HANDLING FuelmixGasoline Two-strokeoilFuelling Chain oilMin 3 m 10ftSTART AND STOP Start and stopStart StopMAINTENANCE Functioning, Basic setting, Final settingBasic setting and running in Fine adjustmentStarter device assembly Starter deviceChanging a broken or worn starter cord Tensioning the recoil springNeedle bearing maintenance Air filterMuffler Spark plugAdjustment of the oil pump Centrifugal cleaning ”Turbo”Heated handles 2149W Cooling systemWeekly maintenance Daily maintenanceMonthly maintenance TECHNICAL DATA Weight34´*xnG¶5g¨ 2149EMISSION CONTROL WARRANTY STATEMENT MANUFACTURER’S WARRANTY COVERAGEOWNER’S WARRANTY RESPONSIBILITIES WARRANTY COMMENCEMENT DATE´*xnG¶5g¨ 1082000W51