Jonsered 2149 manual Start And Stop, Start and stop, Cold engine, Warm engine

Page 28
START AND STOP

START AND STOP

Start and stop

WARNING!

•Never start the saw engine without the bar, chain and clutch cover (chain brake) assembled - or else the clutch can come loose and cause personal injuries.

•Always move the saw away from the fueling area before starting.

•Place the saw on clear ground and make sure that the chain is not contacting anything. Also, make sure that you have a secure footing.

•Keep people and animals well away from the working area.

WARNING!

The catalytic converter muffler gets very hot during and after use. This also applies during idling. Be aware of the fire hazard, especially when handling the saw near flammable substances or vapours.

Start

Grip the front handle with your left hand and hold the saw down by putting your right foot in the rear handle. Pull the starter handle with your right hand and pull out the starter cord slowly until the starter pawls engage. Then pull sharply.

Push in the choke control immediately when the engine ignites and make repeated starting attemps. When the engine starts, rapidly give full throttle. Then the throttle latch will disengage.

Cold engine

CHAIN BRAKE:

Disengage the chain brake by pulling the hand guard towards the front handle.

IGNITION; CHOKE:

Set the choke control in choke position. The stop contact will automatically be set to start position.

FAST IDLE:

Combined choke/fast idle is received when the choke is moved to choke position.

If the saw is fitted with a decompression valve (A): Press the valve to reduce the pressure in the cylinder and make starting easier. Always use the decompression valve when starting the saw. Once the saw has started the valve will automatically return to its original setting.

Warm engine

Use the same procedure as for starting cold engine but without choke. Fast idle is recived by first set the choke control in choke position, and then back again.

H

A

H

CAUTION! Do not release the starter handle from fully pulled out position as this can cause damage on the saw.

Stop

The engine is stopped by switching off the ignition.

28 – English

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Operator´s manual KEY TO SYMBOLS SymbolsCONTENTS ContentsBefore using a new saw Safety instructionsCHAIN SAW SAFETY EQUIPMENT SAFETY INSTRUCTIONSPERSONAL PROTECTIVE EQUIPMENT 1 Chain brake and front hand guard 3 Chain catcher 2 Throttle lock4 Right hand guard 5 Vibration damping system 6 Stop switch7 Muffler 1Checking brake band wear 2 Checking the front hand guard3 Checking the inertia brake release 4Checking the brake triggerSAFETY INSTRUCTIONS CUTTING EQUIPMENT The 5 basic rules1Cutting equipment designed to minimise kickback A BarB Saw chain C Some terms that describe the bar and chainAGeneral information on sharpening cutting teeth B Sharpening cutting teethDSetting the raker clearance C General advice on setting raker clearance3 Tensioning the chain A Chain oil 4 Lubricating cutting equipmentBFilling with chain oil E Needle bearing maintenance C Checking chain lubricationFChecking wear on cutting equipment D Lubricating the bar tip sprocketWhat is kickback? HOW TO AVOID KICKBACKH Bar Do not let go of the handles General rulesNever use the saw one- handed GENERAL SAFETY PRECAUTIONS ”Technical data” section”Maintenance” Min. 3 m1 Basic safety rules GENERAL WORKING INSTRUCTIONS2 Basic cutting technique GeneralTerms Cutting3 Tree felling technique A Safe distanceLimbing B Felling directionC Clearing the trunk and preparing your retreat D FellingDIRECTIONAL CUT FELLING CUTF Cutting the trunk into logs E LimbingAFreeing a “Trapped tree” WHAT IS WHAT? What is what?ASSEMBLY Mounting guide bar and chainFUEL HANDLING FuelmixGasoline Two-strokeoilFuelling Chain oilMin 3 m 10ftSTART AND STOP Start and stopStart StopMAINTENANCE Functioning, Basic setting, Final settingBasic setting and running in Fine adjustmentStarter device assembly Starter deviceChanging a broken or worn starter cord Tensioning the recoil springNeedle bearing maintenance Air filterMuffler Spark plugAdjustment of the oil pump Centrifugal cleaning ”Turbo”Heated handles 2149W Cooling systemDaily maintenance Weekly maintenanceMonthly maintenance TECHNICAL DATA Weight34´*xnG¶5g¨ 2149EMISSION CONTROL WARRANTY STATEMENT MANUFACTURER’S WARRANTY COVERAGEOWNER’S WARRANTY RESPONSIBILITIES WARRANTY COMMENCEMENT DATE108 ´*xnG¶5g¨2000W51
Top Page Image Contents