Jonsered 2149 Contents, Before using a new saw, Safety instructions, What is what?, Assembly

Page 3
CONTENTS

CONTENTS

Before using a new saw

•Read the instructions carefully.

•Check cutting equipment is correctly fitted and adjusted. See page 25.

•Refuel and start the saw. Check the carburetor settings. See pages 26-29.

•Do not use the saw until sufficient chain oil has reached the chain, see page 14.

IMPORTANT! If the carburetor mixture is too lean it greatly increases the risk of engine failure.

Poor maintenance of the air filter will cause carbon build-up on the spark plug and lead to difficult starting.

If the chain is badly adjusted it will cause increased wear or damage to the bar, drive sprocket and chain.

Maintenance, replacement, or repair of the emission control devices and systems may be performed by any nonroad engine repair establishment or individual.

WARNING!

Under no circumstances may the design of the machine be modified without the permis- sion of the manufacturer. Always use genuine spare parts/accessories. Non-authorized modifications and/or accessories can result in serious personal injury or the death of the operator or others.

Your warranty does not cover damage or liability caused by the use of non-authorized accessories or replacement parts.

A chain saw is a dangerous tool if used carelessly or incorrectly and can cause serious, even fatal injuries. It is very important that you read and understand these instructions.

You will find the following labels

on your chain saw:

Contents

Key to symbols

2

Safety instructions

 

Personal protective equipment

4

Chain saw safety equipment

4

Inspecting, maintaining and servicing chain saw safety

 

equipment

8

Cutting equipment

10

How to avoid kickback

16

General safety precautions

18

General working instructions

19

What is what?

 

What is what?

24

Assembly

 

Mounting guide bar and chain

25

Fuel handling

 

Fuelmix

26

Fuelling

27

Start and stop

 

Start and stop

28

Maintenance

 

Carburetor

29

Starter device

30

Air filter

31

Spark plug

31

Muffler

31

Needle bearing maintenance

31

Adjustment of the oil pump

31

Cooling system

32

Centrifugal cleaning ”Turbo”

32

Heated handles (2149W)

32

Winter use

32

Daily maintenance

33

Weekly maintenance

33

Monthly maintenance

33

Technical data

 

2149

34

Emission Control

 

Warranty Statement

 

Your warranty rights and obligations

35

Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice.

English – 3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Operator´s manual Symbols KEY TO SYMBOLSSafety instructions CONTENTSContents Before using a new sawSAFETY INSTRUCTIONS CHAIN SAW SAFETY EQUIPMENTPERSONAL PROTECTIVE EQUIPMENT 1 Chain brake and front hand guard 2 Throttle lock 3 Chain catcher4 Right hand guard 6 Stop switch 5 Vibration damping system7 Muffler 4Checking the brake trigger 1Checking brake band wear2 Checking the front hand guard 3 Checking the inertia brake release3 Chain catcher The 5 basic rules CUTTING EQUIPMENTC Some terms that describe the bar and chain 1Cutting equipment designed to minimise kickbackA Bar B Saw chainB Sharpening cutting teeth AGeneral information on sharpening cutting teethC General advice on setting raker clearance DSetting the raker clearance3 Tensioning the chain 4 Lubricating cutting equipment A Chain oilBFilling with chain oil D Lubricating the bar tip sprocket E Needle bearing maintenanceC Checking chain lubrication FChecking wear on cutting equipmentHOW TO AVOID KICKBACK What is kickback?H Bar General rules Do not let go of the handlesNever use the saw one- handed Min. 3 m GENERAL SAFETY PRECAUTIONS”Technical data” section ”Maintenance”GENERAL WORKING INSTRUCTIONS 1 Basic safety rulesCutting 2 Basic cutting techniqueGeneral TermsB Felling direction 3 Tree felling techniqueA Safe distance LimbingFELLING CUT C Clearing the trunk and preparing your retreatD Felling DIRECTIONAL CUTE Limbing F Cutting the trunk into logsAFreeing a “Trapped tree” What is what? WHAT IS WHAT?Mounting guide bar and chain ASSEMBLYTwo-strokeoil FUEL HANDLINGFuelmix Gasoline10ft FuellingChain oil Min 3 mStop START AND STOPStart and stop StartFine adjustment MAINTENANCEFunctioning, Basic setting, Final setting Basic setting and running inTensioning the recoil spring Starter device assemblyStarter device Changing a broken or worn starter cordSpark plug Needle bearing maintenanceAir filter MufflerCooling system Adjustment of the oil pumpCentrifugal cleaning ”Turbo” Heated handles 2149WWeekly maintenance Daily maintenanceMonthly maintenance 2149 TECHNICAL DATAWeight 34´*xnG¶5g¨WARRANTY COMMENCEMENT DATE EMISSION CONTROL WARRANTY STATEMENTMANUFACTURER’S WARRANTY COVERAGE OWNER’S WARRANTY RESPONSIBILITIES´*xnG¶5g¨ 1082000W51
Top Page Image Contents