Jonsered CS 2188 manual Fuel Handling

Page 18

FUEL HANDLING

Fuel

Note! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stroke oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

 

!

WARNING! Always ensure there is

 

adequate ventilation when handling fuel.

 

 

 

Petrol

•Use good quality unleaded or leaded petrol. Engines equipped with catalytic converters must be run on unleaded fuel mixtures.

•The lowest recommended octane grade is 90 (RON). If you run the engine on a lower octane grade than 90 so-called knocking can occur.This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working with continuous high revs (e.g. limbing) a higher octane is recommended.

Environment fuel

JONSERED recommends the use of alkylate fuel, either Aspen two-stroke fuel or environment fuel for four-stroke engines blended with two-stroke oil as set out below. Note that carburettor adjustment may be necessary when changing the type of fuel (see the instructions under the heading Carburettor).

Running-in

Avoid running at a too high speed during the first 10 hours.

Two-stroke oil

•For the best results and performance use JONSERED two-stroke oil, which is specially formulated for our two-stroke engines.

•JONSERED provides two stroke oils adapted for different application areas and climates. Please contact your dealer for information about the best options for your product and area of application.

•Never use two-stroke oil intended for water-cooled outboard engines, sometimes referred to as outboard oil.

•Never use oil intended for four-stroke engines.

Mixing ratio

1:50 (2%) with JONSERED two-stroke oil.

1:33 (3%) with oils class JASO FB or ISO EGB formulated for air-cooled, two-stroke engines.

Petrol, litre

Two-stroke oil, litre

 

 

 

 

2% (1:50)

3% (1:33)

 

 

 

5

0,10

0,15

 

 

 

10

0,20

0,30

 

 

 

15

0,30

0,45

 

 

 

20

0,40

0,60

 

 

 

Mixing

•Always mix the petrol and oil in a clean container intended for fuel.

•Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol.

•Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank.

•Do not mix more than one month’s supply of fuel at a time.

•If the machine is not used for some time the fuel tank should be emptied and cleaned.

Chain oil

•The chain lubrication system is automatic and we recommend the use of special oil (chain oil) with good adhesion characteristics.

•Never use waste oil. This results in damage to the oil pump, the bar and the chain.

•It is important to use oil of the right grade (suitable viscosity range) to suit the air temperature.

18 – English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operator′s manual English Symbols in the operator’s manual KEY to SymbolsSymbols on the machine Decompression valveThe valve isContents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment General Safety Precautions Fitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFuelling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsLimbing Log is supported at both ends. There is a high riskFelling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentCarburettor with movement limiters Carburettor without movement limiters + 1/4 Checking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Tensioning the recoil spring StarterChanging a broken or worn starter cord Changing a broken recoil springFitting the starter Air filterSpark plug Must always be replacedLubricating the bar tip sprocket Adjustment of the oil pumpCentrifugal cleaning Turbo Needle bearing lubricationTemperature -5C or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 121997, EN ISO Original instructions 1153188-26

CS 2188 specifications

The Jonsered CS 2188 is a powerful chainsaw designed for both professional and serious hobbyist users. Known for its robust performance and durability, it stands out in the competitive market of chainsaws. This model is well-suited for heavy-duty tasks such as felling large trees, cutting firewood, and clearing brush, making it a versatile tool for various applications.

One of the standout features of the Jonsered CS 2188 is its impressive engine performance. Equipped with a high-efficiency 2.1 kW (2.8 hp) engine, it boasts a displacement of 88 cc, allowing it to tackle even the toughest jobs with ease. The engineered design of the power unit ensures that the chainsaw delivers consistent power with a speed of up to 13,500 RPM. This performance translates to faster cutting speeds and improved productivity.

The chainsaw incorporates advanced technologies that enhance its user experience and safety. The unique Clean Power technology minimizes emissions while maximizing fuel efficiency, making it an environmentally friendly option in today's market. This feature is especially important for users conscious of their environmental impact.

Another key characteristic of the Jonsered CS 2188 is its lightweight design combined with optimal balance, which reduces fatigue during prolonged use. The chainsaw features ergonomic handles, providing users with a comfortable grip and better control. This is crucial, especially when working in challenging positions or across various terrains.

The CS 2188 is also equipped with a reliable anti-vibration system that dampens vibrations during operation, further enhancing user comfort and reducing strain on the hands and arms. This system contributes to a smoother cutting experience, allowing for precision work even during extended periods of use.

Maintenance is made simple with the tool-less chain tensioning system, which enables users to adjust the chain tension quickly and efficiently. Coupled with an easy-access air filter, these design features streamline the upkeep process, ensuring the chainsaw remains in optimal working condition.

In summary, the Jonsered CS 2188 is a powerful and dependable chainsaw tailored for users who demand performance, efficiency, and comfort. With its advanced engine technology, ergonomic design, and user-friendly maintenance features, it caters well to both professionals and enthusiasts alike, making it a top choice for anyone needing a reliable cutting tool.
Top Page Image Contents