Jonsered CS 2188 manual Carburettor without movement limiters

Page 31

MAINTENANCE

Rec. idle speed: 2700 rpm

WARNING! Contact your servicing

! dealer, if the idle speed setting cannot be adjusted so that the chain stops. Do not use the chain saw until it has been properly adjusted or repaired.

Fine adjustment

When the machine has been ”run-in” the carburettor should be finely adjusted. The fine adjustment should be carried out by a qualified person. First adjust the L-jet, then the idling screw T and then the H-jet.

Changing the type of fuel

Fine tuning may be required if the chain saw, after changing the type of fuel, performs differently with regard to starting, acceleration, maximum speed, etc.

Conditions

•Before any adjustments are made the air filter should be clean and the cylinder cover fitted. Adjusting the carburettor while a dirty air filter is in use will result in a leaner mixture next time the filter is cleaned. This can give rise to serious engine damage.

•Do not attempt to adjust the L and H jets beyond either stop as this could cause damage.

•Now start the machine according to the starting instructions and let it warm up for 10 minutes.

CAUTION! If the chain rotates while idling the T- screw must be turned anti-clockwise until the chain stops.

•Place the machine on a flat surface so that the bar points away from you and so that the bar and chain do not come into contact with the surface or other objects.

Low speed jet L

Turn the low speed jet L clockwise until it stops. If the engine accelerates poorly or idles unevenly, turn the low speed jet L anticlockwise until good acceleration and idling are achieved.

CAUTION! If the chain rotates while idling theT-screw must be turned anti-clockwise until the chain stops.

Fine adjustment of the idle speed T

Adjust the idle speed with the T-screw. If it is necessary to re-adjust, turn the T-screw clockwise while the engine is running, until the chain starts to rotate. Then turn anti- clockwise until the chain stops. When the idle speed is correctly adjusted the engine should run smoothly in

every position and the engine speed should be safely below the speed at which the chain starts to rotate.

WARNING! Contact your servicing

! dealer, if the idle speed setting cannot be adjusted so that the chain stops. Do not use the chain saw until it has been properly adjusted or repaired.

High speed jet H

At the factory the engine is adjusted at sea level. When working at a high altitude or in different weather conditions, temperatures and atmospheric humidity, it may be necessary to make minor adjustments to the high speed jet.

CAUTION! If the high speed jet is screwed in too far, it may damage the piston/cylinder.

When test run at the factory, the high speed jet is set so that the engine satisfies the applicable legal requirements at the same time as achieving maximum performance.

The carburettor’s high speed jet is then locked using a limiter cap in the fully screwed out position.The limiter cap limits the potential to adjust the high speed jet to at most half a turn.

CAUTION! There is an integrated speed governor in the ignition system that limits the maximum speed to 13000 rpm. The maximum speed will not exceed 13000 rpm when the high speed jet is adjusted (screwed in). When the speed governor is activated, you will get the same sound experience as when the chain saw 4-cycles.

To adjust the carburettor correctly you should contact a mechanic with access to a rev counter.

CAUTION! As the spark is cut off, the rev counter does not show speeds higher than 13000 rpm.

Correctly adjusted carburettor

When the carburettor is correctly adjusted the machine accelerates without hesitation and 4-cycles a little at full throttle. It is also important that the chain does not rotate at idle. If the L-jet is set too lean it may cause starting difficulties and poor acceleration. If the H-jet is set too lean the machine will have less power, poor acceleration and could suffer damage to the engine.

Carburettor without movement limiters

English – 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Operator′s manual English Decompression valveThe valve is KEY to SymbolsSymbols on the machine Symbols in the operator’s manualContents Dear Customer IntroductionWhat is what on the chain saw? What is WHAT?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerInjuries Some terms that describe the bar and chain Cutting equipment designed to reduce kickbackBar ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Checking chain lubrication Lubricating cutting equipmentWhich could lead to serious, even fatal injuries Chain oil Filling with chain oilNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment General Safety Precautions Working with the chain AssemblyFitting the bar and chain Fitting a spike bumperFuel Fuel HandlingLong-term storage Fuel safetyFuelling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useJam. Always stop the engine before cleaning Terms Basic cutting techniqueLog is supported at both ends. There is a high risk LimbingClearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburettor adjustment MaintenanceCarburettor with movement limiters Carburettor without movement limiters + 1/4 Checking the front hand guard Checking brake band wearImmediately Checking the inertia brake releaseMuffler Changing a broken recoil spring StarterChanging a broken or worn starter cord Tensioning the recoil springMust always be replaced Air filterSpark plug Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpCentrifugal cleaning Turbo Lubricating the bar tip sprocketTemperature -5C or colder Daily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical DataSaw chain filing and file gauges Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 121997, EN ISO Original instructions 1153188-26

CS 2188 specifications

The Jonsered CS 2188 is a powerful chainsaw designed for both professional and serious hobbyist users. Known for its robust performance and durability, it stands out in the competitive market of chainsaws. This model is well-suited for heavy-duty tasks such as felling large trees, cutting firewood, and clearing brush, making it a versatile tool for various applications.

One of the standout features of the Jonsered CS 2188 is its impressive engine performance. Equipped with a high-efficiency 2.1 kW (2.8 hp) engine, it boasts a displacement of 88 cc, allowing it to tackle even the toughest jobs with ease. The engineered design of the power unit ensures that the chainsaw delivers consistent power with a speed of up to 13,500 RPM. This performance translates to faster cutting speeds and improved productivity.

The chainsaw incorporates advanced technologies that enhance its user experience and safety. The unique Clean Power technology minimizes emissions while maximizing fuel efficiency, making it an environmentally friendly option in today's market. This feature is especially important for users conscious of their environmental impact.

Another key characteristic of the Jonsered CS 2188 is its lightweight design combined with optimal balance, which reduces fatigue during prolonged use. The chainsaw features ergonomic handles, providing users with a comfortable grip and better control. This is crucial, especially when working in challenging positions or across various terrains.

The CS 2188 is also equipped with a reliable anti-vibration system that dampens vibrations during operation, further enhancing user comfort and reducing strain on the hands and arms. This system contributes to a smoother cutting experience, allowing for precision work even during extended periods of use.

Maintenance is made simple with the tool-less chain tensioning system, which enables users to adjust the chain tension quickly and efficiently. Coupled with an easy-access air filter, these design features streamline the upkeep process, ensuring the chainsaw remains in optimal working condition.

In summary, the Jonsered CS 2188 is a powerful and dependable chainsaw tailored for users who demand performance, efficiency, and comfort. With its advanced engine technology, ergonomic design, and user-friendly maintenance features, it caters well to both professionals and enthusiasts alike, making it a top choice for anyone needing a reliable cutting tool.
Top Page Image Contents