Jonsered CS 2188 Maintenance schedule, Daily maintenance Weekly maintenance Monthly maintenance

Page 40

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section.

Daily maintenance

Weekly maintenance

Monthly maintenance

 

 

 

 

On chain saws without a catalytic

Check the brake band on the chain

 

brake for wear. Replace when less

Clean the outside of the machine.

converter, check the cooling system

than 0.6 mm (0,024 inch) remains at

 

weekly.

 

the most worn point.

 

 

 

 

 

Check that the components of the

Check the starter, starter cord and

Check the clutch centre, clutch drum

throttle control work safely. (Throttle

return spring.

and clutch spring for wear.

lockout and throttle control.)

 

 

 

 

 

Clean the chain brake and check that

 

 

it operates safely. Make sure that the

Check that the vibration damping

Clean the spark plug. Check that the

chain catcher is undamaged, and

elements are not damaged.

electrode gap is 0.5 mm.

replace it if necessary.

 

 

 

 

 

The bar should be turned daily for

 

 

more even wear. Check the

 

 

lubrication hole in the bar, to be sure it

Lubricate the clutch drum bearing.

Clean the outside of the carburettor.

is not clogged. Clean the bar groove.

If the bar has a sprocket tip, this

 

 

should be lubricated.

 

 

 

 

 

Check that the bar and chain are

File off any burrs from the edges of

Check the fuel filter and the fuel hose.

getting sufficient oil.

the bar.

Replace if necessary.

 

 

 

Check the saw chain with regard to

 

 

visible cracks in the rivets and links,

 

 

whether the saw chain is stiff or

Clean or replace the spark arrestor

Empty the fuel tank and clean the

whether the rivets and links are

mesh on the muffler.

inside.

abnormally worn. Replace if

 

 

necessary.

 

 

 

 

 

Sharpen the chain and check its

 

 

tension and condition.Check the drive

Clean the carburettor compartment.

Empty the oil tank and clean the

sprocket for excessive wear and

 

inside.

replace if necessary.

 

 

 

 

 

Clean the starter units air intake.

Clean the air filter. Replace if

Check all cables and connections.

necessary.

 

 

 

 

 

Check that nuts and screws are tight.

 

 

 

 

 

Check that the stop switch works

 

 

correctly.

 

 

 

 

 

Check that there are no fuel leaks

 

 

from the engine, tank or fuel lines.

 

 

 

 

 

On chain saws with a catalytic

 

 

converter, check the cooling system

 

 

daily.

 

 

 

 

 

40 – English

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Operator′s manual English KEY to Symbols Symbols on the machineSymbols in the operator’s manual Decompression valveThe valve isContents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesCutting equipment designed to reduce kickback BarChain Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilFilling with chain oil Checking chain lubricationNeedle bearing lubrication Chain drive sprocketChecking wear on cutting equipment General Safety Precautions Assembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelFuel safety FuellingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsLimbing Log is supported at both ends. There is a high riskTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburettor adjustment MaintenanceCarburettor with movement limiters Carburettor without movement limiters + 1/4 Checking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir filter Spark plugFitting the starter Must always be replacedAdjustment of the oil pump Centrifugal cleaning TurboLubricating the bar tip sprocket Needle bearing lubricationTemperature -5C or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 121997, EN ISO Original instructions 1153188-26

CS 2188 specifications

The Jonsered CS 2188 is a powerful chainsaw designed for both professional and serious hobbyist users. Known for its robust performance and durability, it stands out in the competitive market of chainsaws. This model is well-suited for heavy-duty tasks such as felling large trees, cutting firewood, and clearing brush, making it a versatile tool for various applications.

One of the standout features of the Jonsered CS 2188 is its impressive engine performance. Equipped with a high-efficiency 2.1 kW (2.8 hp) engine, it boasts a displacement of 88 cc, allowing it to tackle even the toughest jobs with ease. The engineered design of the power unit ensures that the chainsaw delivers consistent power with a speed of up to 13,500 RPM. This performance translates to faster cutting speeds and improved productivity.

The chainsaw incorporates advanced technologies that enhance its user experience and safety. The unique Clean Power technology minimizes emissions while maximizing fuel efficiency, making it an environmentally friendly option in today's market. This feature is especially important for users conscious of their environmental impact.

Another key characteristic of the Jonsered CS 2188 is its lightweight design combined with optimal balance, which reduces fatigue during prolonged use. The chainsaw features ergonomic handles, providing users with a comfortable grip and better control. This is crucial, especially when working in challenging positions or across various terrains.

The CS 2188 is also equipped with a reliable anti-vibration system that dampens vibrations during operation, further enhancing user comfort and reducing strain on the hands and arms. This system contributes to a smoother cutting experience, allowing for precision work even during extended periods of use.

Maintenance is made simple with the tool-less chain tensioning system, which enables users to adjust the chain tension quickly and efficiently. Coupled with an easy-access air filter, these design features streamline the upkeep process, ensuring the chainsaw remains in optimal working condition.

In summary, the Jonsered CS 2188 is a powerful and dependable chainsaw tailored for users who demand performance, efficiency, and comfort. With its advanced engine technology, ergonomic design, and user-friendly maintenance features, it caters well to both professionals and enthusiasts alike, making it a top choice for anyone needing a reliable cutting tool.
Top Page Image Contents