Jonsered CS 2188 Starter, Changing a broken or worn starter cord, Tensioning the recoil spring

Page 36

MAINTENANCE

use a muffler if the spark arrestor mesh is missing or defective.

The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. The exhaust gases are hot and can contain sparks, which may cause fire if directed against dry and combustible material.

A muffler equipped with a catalytic converter significantly reduces the amount of hydrocarbons (HC), nitrogen oxides (NO) and aldehydes in the exhaust fumes. Carbon monoxide (CO), which is poisonous and odourless, is not however reduced! Consequently, never work in an enclosed or badly ventilated area. Good air circulation should always prevail when working in snowy hollows, ravines or in confined conditions.

Starter

WARNING! When the recoil spring is

!wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury.

Care must be exercised when replacing the return spring or the starter cord. Wear protective glasses and protective gloves.

Changing a broken or worn starter cord

•Loosen the screws that hold the starter against the crankcase and remove the starter.

•Pull out the cord approx. 30 cm and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the centre of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned at least a further 1/2 turn when the starter cord is pulled all the way out.

Changing a broken recoil spring

•Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord.

36 – English

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Operator′s manual English KEY to Symbols Symbols on the machineSymbols in the operator’s manual Decompression valveThe valve isContents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesCutting equipment designed to reduce kickback BarChain Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment General Safety Precautions Assembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelFuel safety FuellingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsLimbing Log is supported at both ends. There is a high riskTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentCarburettor with movement limiters Carburettor without movement limiters + 1/4 Checking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir filter Spark plugFitting the starter Must always be replacedAdjustment of the oil pump Centrifugal cleaning TurboLubricating the bar tip sprocket Needle bearing lubricationTemperature -5C or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 121997, EN ISO Original instructions 1153188-26

CS 2188 specifications

The Jonsered CS 2188 is a powerful chainsaw designed for both professional and serious hobbyist users. Known for its robust performance and durability, it stands out in the competitive market of chainsaws. This model is well-suited for heavy-duty tasks such as felling large trees, cutting firewood, and clearing brush, making it a versatile tool for various applications.

One of the standout features of the Jonsered CS 2188 is its impressive engine performance. Equipped with a high-efficiency 2.1 kW (2.8 hp) engine, it boasts a displacement of 88 cc, allowing it to tackle even the toughest jobs with ease. The engineered design of the power unit ensures that the chainsaw delivers consistent power with a speed of up to 13,500 RPM. This performance translates to faster cutting speeds and improved productivity.

The chainsaw incorporates advanced technologies that enhance its user experience and safety. The unique Clean Power technology minimizes emissions while maximizing fuel efficiency, making it an environmentally friendly option in today's market. This feature is especially important for users conscious of their environmental impact.

Another key characteristic of the Jonsered CS 2188 is its lightweight design combined with optimal balance, which reduces fatigue during prolonged use. The chainsaw features ergonomic handles, providing users with a comfortable grip and better control. This is crucial, especially when working in challenging positions or across various terrains.

The CS 2188 is also equipped with a reliable anti-vibration system that dampens vibrations during operation, further enhancing user comfort and reducing strain on the hands and arms. This system contributes to a smoother cutting experience, allowing for precision work even during extended periods of use.

Maintenance is made simple with the tool-less chain tensioning system, which enables users to adjust the chain tension quickly and efficiently. Coupled with an easy-access air filter, these design features streamline the upkeep process, ensuring the chainsaw remains in optimal working condition.

In summary, the Jonsered CS 2188 is a powerful and dependable chainsaw tailored for users who demand performance, efficiency, and comfort. With its advanced engine technology, ergonomic design, and user-friendly maintenance features, it caters well to both professionals and enthusiasts alike, making it a top choice for anyone needing a reliable cutting tool.
Top Page Image Contents