Jonsered CS 2188 manual Basic cutting technique, Terms

Page 24

WORKING TECHNIQUES

ladder, in a tree or where you do not have firm ground to stand on.

6Always use a fast cutting speed, i.e. full throttle.

7Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is known as cutting on the push stroke.The chain tries to push the chain saw back towards the user. If the saw chain is jamming, the saw may be pushed back at you.

8Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which will lead to a kickback.

Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting on the pull stroke. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting on the pull stroke gives the operator better control over the chain saw and the position of the kickback zone.

9Follow the instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only combinations that are recommended by us. See instructions under the headings Cutting equipment and Technical data.

Basic cutting technique

WARNING! Never use a chain saw by ! holding it with one hand. A chain saw is

not safely controlled with one hand. Always have a secure, firm grip around the handles with both hands.

General

•Always use full throttle when cutting!

•Reduce the speed to idle after every cut (running the engine for too long at full throttle without any load, i.e. without any resistance from the chain during cutting, can lead to serious engine damage).

•Cutting from above = Cutting on the pull stroke.

•Cutting from below = Cutting on the push stroke.

Cutting on the push stroke increases the risk of kickback. See instructions under the heading How to avoid kickback.

Terms

Cutting = General term for cutting through wood.

Limbing = Cutting branches off a felled tree.

Splitting = When the object you are cutting breaks off before the cut is complete.

There are five important factors you should consider before making a cut:

1Make sure the cutting equipment will not jam in the cut.

2Make sure the object you are cutting will not split.

3Make sure the chain will not strike the ground or any other object during or after cutting.

4Is there a risk of kickback?

24 – English

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operator′s manual English KEY to Symbols Symbols on the machineSymbols in the operator’s manual Decompression valveThe valve isContents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesCutting equipment designed to reduce kickback BarChain Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilFilling with chain oil Checking chain lubricationChain drive sprocket Needle bearing lubricationChecking wear on cutting equipment General Safety Precautions Assembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelFuel safety FuellingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsJam. Always stop the engine before cleaning Basic cutting technique TermsLimbing Log is supported at both ends. There is a high riskTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburettor adjustmentCarburettor with movement limiters Carburettor without movement limiters + 1/4 Checking brake band wear Checking the front hand guardChecking the inertia brake release ImmediatelyMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring Changing a broken recoil springAir filter Spark plugFitting the starter Must always be replacedAdjustment of the oil pump Centrifugal cleaning TurboLubricating the bar tip sprocket Needle bearing lubricationTemperature -5C or colder Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesEC-declaration of conformity Applies to Europe onlyEN ISO 12100-22003, Cispr 121997, EN ISO Original instructions 1153188-26

CS 2188 specifications

The Jonsered CS 2188 is a powerful chainsaw designed for both professional and serious hobbyist users. Known for its robust performance and durability, it stands out in the competitive market of chainsaws. This model is well-suited for heavy-duty tasks such as felling large trees, cutting firewood, and clearing brush, making it a versatile tool for various applications.

One of the standout features of the Jonsered CS 2188 is its impressive engine performance. Equipped with a high-efficiency 2.1 kW (2.8 hp) engine, it boasts a displacement of 88 cc, allowing it to tackle even the toughest jobs with ease. The engineered design of the power unit ensures that the chainsaw delivers consistent power with a speed of up to 13,500 RPM. This performance translates to faster cutting speeds and improved productivity.

The chainsaw incorporates advanced technologies that enhance its user experience and safety. The unique Clean Power technology minimizes emissions while maximizing fuel efficiency, making it an environmentally friendly option in today's market. This feature is especially important for users conscious of their environmental impact.

Another key characteristic of the Jonsered CS 2188 is its lightweight design combined with optimal balance, which reduces fatigue during prolonged use. The chainsaw features ergonomic handles, providing users with a comfortable grip and better control. This is crucial, especially when working in challenging positions or across various terrains.

The CS 2188 is also equipped with a reliable anti-vibration system that dampens vibrations during operation, further enhancing user comfort and reducing strain on the hands and arms. This system contributes to a smoother cutting experience, allowing for precision work even during extended periods of use.

Maintenance is made simple with the tool-less chain tensioning system, which enables users to adjust the chain tension quickly and efficiently. Coupled with an easy-access air filter, these design features streamline the upkeep process, ensuring the chainsaw remains in optimal working condition.

In summary, the Jonsered CS 2188 is a powerful and dependable chainsaw tailored for users who demand performance, efficiency, and comfort. With its advanced engine technology, ergonomic design, and user-friendly maintenance features, it caters well to both professionals and enthusiasts alike, making it a top choice for anyone needing a reliable cutting tool.
Top Page Image Contents