Marantz ZR6001 Surround, 5PL II PRO LOGIC II MUSIC PARAMETER, 6CS II CIRCLE SURROUND II PARAMETER

4 SURROUND

4 S URROUND

S URR . MOD E	: AU T O
H T - EQ	: O F F
L F E L E V E L	: 0 d B

MA I N E X I T

1. Select “SURROUND” in the SETUP MAIN

MENU with the or cursor buttons, and press the ENTER button.

2. To select a desired content , press the or cursor buttons.

SURR.MODE:

Select the desired surround mode with the or cursor buttons.

HT-EQ:

Select to active the HT-EQ with the or cursor buttons.

The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because film soundtracks were designed to be played back in large movie theater environments. Activating the HT-EQ feature when watching a film made for movie theaters corrects this and restores the correct tonal balance.

The HT-EQ feature is available except in the following modes.

•7.1 CH INPUT

•PURE-DIRECT

•When VIRTUAL is set for the surround mode

LFE LEVEL:

Select the output level of the LFE signal included in the Dolby Digital signal or the DTS signal.

Select 0 dB, -10 dB or OFF with the or cursor buttons.

After you complete this portion of the set up, move the cursor to “MAIN” with the or cursor buttons and press the ENTER button.

5PL II (PRO LOGIC II) MUSIC PARAMETER

Pro Logic II-Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs.

In this mode, ZR6001 includes three controls to fine-tune the soundfield as follows.

5 P L II MUS I C	PARAME T ER
PARAME T ER	: DE F AU L T
PANORAMA	: OF F
D I MEN S I ON	:	3
CEN T E R W I D T H	:	3
MA I N		E X I T

Select “PL II MUSIC” in the SETUP MAIN MENU

with the or cursor buttons, and press the ENTER button.

PARAMETER:

Select “DEFAULT” or “CUSTOM” with the or cursor buttons.

If you select “CUSTOM”, you can adjust three parameters as listed below.

PANORAMA:

Select the Panorama mode On or Off with the or cursor buttons.

Panorama wraps the sound of the front left and right speakers around you, for an exciting perspective.

DIMENSION:

Set the Dimension level between 0 and 6 level in 1 level intervals with the or cursor buttons. Adjust the soundfield either towards the front or towards the rear.

This can be useful to help achieve a more suitable balance from all the speakers with certain recordings.

CENTER WIDTH:

Set the Center width level between 0 and 7 in 1 level intervals with the or cursor buttons. Center Width allows you to gradually spread the center channel sound into the front left and right speakers.

At its widest setting, all the sound from the center is mixed into the left and right.

This control may help achieve a more spacious sound or a better blend for the front image.

If “NONE” was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear.

After you complete this portion of the set up, move cursor to “MAIN” with the or cursor buttons and press the ENTER button.

6CS II (CIRCLE SURROUND II) PARAMETER

6 C S II P ARAME T E R

T RUBA S S	:	0
S R S D I A L OG	:	0

	MA I N		E X I T
1.	Select “CS II” in the SETUP MAIN MENU with
	the	or	cursor buttons, and press the
2.	ENTER button.
	To Select desired contents as below, press
	the	or	cursor buttons.

TRUBASS:

Set the TRUBASS level between 0 and 6 level in 1 level interval with the or cursor buttons. TRUBASS produced by the speakers are an octave below the actual physical capabilities of the speakers adding exciting, deeper bass effects.

SRS DIALOG:

Set the SRS DIALOG level between 0 and 6 in 1 level intervals with the or cursor buttons. This can be popped out of the surround audio effects, allowing the listener to easily discern what the actors say.

If “NONE” was selected for the Center speaker setting, in the Speaker size set up menu, then this setting will not appear.

After you complete this portion of the set up, move cursor to “MAIN” with the or cursor buttons and press the ENTER button.

7 MULTI ROOM

ZR6001 has features in MULTI ROOM SYSTEM such as source selector, sleep timer, Multi Room Speaker output and remote control.

You can set these feature in this sub-menu.

	7	MU L T I	ROOM
	A UD I O		:	D V D
	S L E E P T I ME R		: O F F
	MU L T I : OF F		MS PK B : ✽ ✽ ✽
	V OL	: VAR I	VOL	: ✽ ✽ ✽
	L E V E L : - 9 0 d B L E V E L : ✽ ✽ ✽
	- - - - MA I N - ROOM S T A T US - - - -
	V I DEO : DVD		AUD I O : DVD
	MA I N			E X I T
1.
	Select	“MULTI ROOM” in the SETUP MAIN
	MENU with or		cursor button, and press
2.	the ENTER button.
	To Select desired contents, press or

cursor button

AUDIO:

Select the audio source of the Multi-room output with or cursor buttons.

SLEEP TIMER:

SLEEP timer function is available during the

multiroom is active, set the time with or cursor buttons.

MULTI (MULTI ROOM):

To switch on the Multi-room output ON or OFF, press or cursor button.

VOL (VOLUME SETUP):

Select whether the Multi-room output level is variable or fixed with a or cursor buttons.

LEVEL (VOLUME LEVEL):

Adjust the Multi-room output level with or cursor buttons.

MSPK B (MULTI SPEAKER B):

To switch on the Multi-speaker B output ON or OFF, press or cursor buttons.

Note:

•This setting can be changed when the Surr Back is

set “NONE” in 2-1 SPEAKER SIZE menu. When this setting is unavailable, “✽ ✽ ✽ ” is displayed

VOL (VOLUME SETUP):

Select whether the Multi-speaker output level is variable or fixed with a or cursor buttons.

Note:

•This setting can be changed when the Surr Back is set “NONE” in 2-1 SPEAKER SIZE menu. When this setting is unavailable, “✽ ✽ ✽ ” is displayed

ENGLISH

23