2. 4. 2. 5. 1, Preset Memory, Using the ZR6001

ENGLISH	(FM) TUNING MODE (AUTO STEREO OR MONO)
ENGLISH				T-MODE	RDS	F.DIRECT
			INPUT/DISC+	AUDIO	SUB-T/ATT	PTY
			CH.SEL			LIP.SYNC
	DISPLAY	MEMORY	CLEAR
			SYSTEM REMOTE CONTROLLER
				RC5500SR
	ENTER
	EXIT	BAND	T-MODE

When in the auto stereo mode, AUTO indicator will be illuminated on the display.

The “ST” indicator is illuminated when a stereo broadcast is tuned in.

At open frequencies, the noise is muted and the “TUNED” and “ST” indicators are not illuminated. If the signal is weak, it may be difficult to tune into the station in stereo. In such a case, press the T-MODEbutton on the front panel or remote. “AUTO” indicator is not illuminated, if FM stereo broadcasts are received in monaural and the “ST” indicator is not illuminated.

To return to auto stereo mode, press the T-MODEbutton or press T-MODEbutton on the remote again. AUTO indicator is illuminated on the display.

PRESET MEMORY

With this unit you can preset up to 50 FM/AM stations in any order.

For each station, you can memorize the frequency and reception mode if desired.

AUTO PRESET MEMORY

This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory.

2. 4. 2. 5. 1. 3.

SURROUND	PURE	SIMPLE
MODE	DIRECT	SETUP	DISPLAY	MEMORY	CLEAR
			ENTER
AUTO	HT-EQ	MENU	EXIT	BAND	T-MODE

1. To select FM , press the BAND button on the front panel.

2. While pressing the MEMO button, press the cursor button.

“AUTO PRESET” will appear on the display, and scanning starts from the lowest frequency.

3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds.

During this time, the following operations are possible.

The band can be changed by the BAND button.

4. If no button is pressed during this period, the current station is memorized in location Preset 02.

If you wish to skip the current station, press

the cursor button during this period, this station is skipped and auto presetting continues.

5. Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button.

MANUAL PRESET MEMORY

		3.		2. 4.					ENTER
								SET UP/		MENU OFF
								T.TONE
								PURE DIRECT	AUTO		DTS
							3.		1	2	3
								NIGHT	CSII	EX/ES	VIRTUAL
									4	5	6
								DISPLAY	MCH-ST	STEREO	7.1CH IN
							2.		7	8	9
SURROUND	PURE	SIMPLE						CLEAR	MEMO	A/D	P.SCAN/V-OFF
MODE	DIRECT	SETUP		DISPLAY	MEMORY	C				0
										0
AUTO	HT-EQ	MENU	ENTER	EXIT	BAND	T				CHANNEL/SKIP

BASS TREBLE TUNE/SEARCH

T-MODE RDS F.DIRECT

(Using the ZR6001)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the front panel. “– –“ (preset number) starts blinking on the display.

3. Select the preset number by pressing theor

cursor buttons, while this is still blinking (approx. 5 seconds)

4. Press the MEMO button again to enter. The display stops blinking.

The station is now stored in the specified preset memory location.

(Using the remote control unit)

1. Tune into the radio station you desire (Refer to the “MANUAL TUNING” or “AUTO TUNING” section).

2. Press the MEMO button on the remote. “– –“ (preset number) starts blinking on the display.

3. Enter the desired preset number by pressing the numeric buttons.

Note:

•When entering a single digit number (2 for example), either input “02” or just input “2” and wait for a few seconds.

RECALLING A PRESET STATION

		1.					SET UP/		MENU OFF
							T.TONE
							PURE DIRECT	AUTO		DTS
						1.		1	2	3
							NIGHT	CSII	EX/ES	VIRTUAL
								4	5	6
							DISPLAY	MCH-ST	STEREO	7.1CH IN
								7	8	9
							CLEAR	MEMO	A/D	P.SCAN/V-OFF
						1.			0
SURROUND	PURE	SIMPLE							CHANNEL/SKIP
MODE	DIRECT	SETUP	DISPLAY	MEMORY	CLEAR				CHANNEL/SKIP
			ENTER
AUTO	HT-EQ	MENU	EXIT	BAND	T-MODE		BASS	TREBLE	TUNE/SEARCH
								T-MODE	RDS	F.DIRECT

(Using the ZR6001)

1. Select the desired preset station by pressing theorcursor buttons on the front panel

(Using the remote control unit)

1. Press the 4 or ¢ buttons to select the desired preset station, or input your desired preset channel with the numeric buttons on the remote.

PRESET SCAN

	SET UP/		MENU OFF
	T.TONE
	PURE DIRECT	AUTO		DTS
		1	2	3
	NIGHT	CSII	EX/ES	VIRTUAL
		4	5	6	1.
	DISPLAY	MCH-ST	STEREO	7.1CH IN
		7	0	9
3.	CLEAR	MEMO	A/D	P.SCAN/V-OFF	3.
			CHANNEL/SKIP		3.
			CHANNEL/SKIP
3.	BASS	TREBLE	TUNE/SEARCH
3.		T-MODE	RDS	F.DIRECT
	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY
	CH SEL			LIP SYNC

(Using the remote control unit)

1. Press the P.SCAN on the remote.

“PRESET SCAN” appears on the display and then the preset station with the lowest preset number is recalled first.

2. Preset stations are recalled in sequence (No.1

→No.2 → etc.) for 5 seconds each.

No stored preset number will be skipped.

3. You can fast forward the preset stations by pressing the ¢ continuously.

When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P.SCAN on the remote.