Marantz LN-11S1A manual Introduction, Contents

INTRODUCTION

ABOUT THIS USER’S GUIDE

Before mounting the LN-11S1A, be sure to thoroughly read the projector’s user’s guide and decide on the mounting location.

A Marantz ceiling mount kit, MOUNT20, is required if you will be using a Marantz VP11 or VP15 series projector suspended from the ceiling. Be sure to use an EXT10 to adjust the suspension height.

This User’s Guide serves as a setup guide that describes how to assemble the MOUNT20 and EXT10, and mount the LN-11S1A.

For details on the space required for mounting, refer to the figure showing the movable range at the end of this guide.

If the LN-11S1A lens slider was moved by hands, it might cause failure. Do not move the lens slider by hands.

A Phillips-head screwdriver, hexagon wrench, and spanner are required in order to assemble the LN- 11S1A, EXT10, and MOUNT20.

If you look into the lens during projection, light will enter your eyes, possibly resulting in eye pain and/ or problems of vision.

During cleaning, unplug the power cord of the AC adapter from the power outlet. For safety, always unplug the power cord from the power outlet at times when the unit will not be used for an extended period, such as when you are out or on vacation.

CONTENTS
BEFORE USE	2
CHECKING THE UNIT AND SUPPLIED ACCESSORIES	2
NAMES OF PARTS	2
BASIC OPERATION	3
TURNING THE POWER ON	3
TURNING THE POWER OFF	3
CONTROLLING THE UNIT USING A TRIGGER INPUT SIGNAL	3
USING VP-11 OR VP-15 SERIES TRIG. 2 OUTPUT JACK	3
CONCERNING CONNECTORS AND CABLES	4
ADVANCED OPERATION	5
USING A PROGRAMMABLE REMOTE CONTROLLER	5

BASIC OPERATION NAME OF PARTS BEFORE USE

IMPORTANT

Note:

The lens used in this product is a finely crafted, precision optical device. It may be scratched or even damaged from physical contact with objects of any type.

Such contact and/or improper handling must therefore be avoided. Please note before use that scratches caused by the user, whether intentional or accidental, and damage to the lens due to other external causes are outside the scope of the warrantee.

Do not connect the AC/DC adapter supplied with the anamorphic lens system to the lens slider or power outlet until a projector (VP-11/VP-15), anamorphic lens system (LN-11S1A), and bracket (MOUNT20/ EXT10) are completely mounted.

For information on other connections, refer to the user’s guide for the device that is to be connected to the LN-11S1A anamorphic lens system.

To avoid accidentally scratching the lens surface during mounting, hundle the lens with the most careful attention.

The LN-11S1A lens slider uses a special motor and several types of gears. If water or foreign matter enters the LN-11S1A lens slider, damage to the equipment or fire may result. If water or foreign matter should enter the unit, immediately unplug the power cord of the AC adapter and contact our Customer Service Center.

BEFORE USE

NOTE ON ASSEMBLY

Securely attach the anamorphic lens, lens slider, and base plate using the provided metal screws.

NOTE ON MOUNTING

Even when attaching this unit to the projector, be sure to use the specified screws and to attach the unit securely. Also, the anamorphic lens moves left and right.

Take care that there are no obstacles within the range of motion of the lens.

Special skill and experience are required when mounting the projector and this unit to a ceiling. When mounting, please consult your dealer.

NOTES WHEN SIMULTANEOUSLY USING +12 V TRIGGER INPUT AND remote controller	5
FIXING THE ANAMORPHIC LENS POSITION	5
SETUP	5
SETUP PROCEDURE	6
EXT10 ASSEMBLY	6
Preparing the LN-11S1A	7
Assembling the MOUNT20	7
Mounting the LN-11S1A (On the ceiling)	9
Mounting the LN-11S1A (On the floor)	10
Mounting the LN-11S1A Lens	10
Connecting the LN-11S1A	10
Adjusting the LN-11S1A Lens	11
TROUBLESHOOTING	12
others	12
Projection distance chart For vp-11 and vp-15 projectors	12
SPECIFICATIONS & DIMENSIONS	13

ADVANCED OTHERS TROUBLESHOOTING SETUP OPERATION

1