Homelite CSP3816, CSP4518 Basic OPERATING/CUTTING Procedures, Work Area Precautions, AIR Filter

Page 18

OPERATION

BASIC OPERATING/CUTTING PROCEDURES

Practise cutting a few small logs using the following technique, to get the “feel” of using your saw before you begin a major sawing operation.

1.Take the proper stance in front of the wood with the saw idling.

2.Accelerate the engine to full throttle just before entering the cut by squeezing the throttle trigger.

3.Begin cutting with the saw against the log.

4.Keep the engine at full throttle the entire time you are cutting.

5.Allow the chain to cut for you; exert only light downward pressure. Forcing the cut could result in damage to the bar, chain or engine.

6.Release the throttle trigger as soon as the cut is completed allowing the engine to idle. Running the saw at full throttle without a cutting load can result in unnecessary wear to the chain, bar and engine.

7.Do not put pressure on the saw at the end of the cut.

WORK AREA PRECAUTIONS

Cut only wood or materials made from wood; no sheet metal, no plastics, no masonry, no non-wood building materials.

Never allow children to operate your saw. Allow no person to use this chainsaw who has not read this operator’s manual or received adequate instructions for the safe and proper use of this chainsaw.

Keep everyone – helpers, bystanders, children and animals—a SAFE DISTANCE from the cutting area. During felling operations, the safe distance should be a least twice the height of the largest trees in the felling area. During bucking operations, keep a minimum distance of 4.5 m (15 ft) between workers.

ADJUSTING THE CARBURETTOR

Before adjusting the carburettor, clean the air filter and the starter cover vents. Allow the engine to warm up before carburettor adjustment. Refer to “Maintenance” later in this manual.

AIR FILTER

Fig. 24

STARTER COVER

Fig. 25

VENTS

The carburettor is factory set and should not require adjust- ing.The carburettor will permit only limited adjustment of the “L” Low Jet) and “H” High Jet) needles. Any adjustment should be done by a Homelite service dealer.

Under no circumstances should the “L” Low Jet) and “H” High Jet) needles be forced outside the range of adjustment.

CAUTION:

Serious damage may occur to the engine if improper adjustments are made to the “L” and “H” needles.

Do not force the “L” and “H” needles outside the adjustment range!

Fig. 23

Always cut with both feet on solid ground to prevent being pulled off balance.

Do not cut above chest height, as a saw held higher is difficult to control against kick-back forces.

Do not fell trees near electrical wires or buildings. Leave this operation for professionals.

Cut only when visibility and light are adequate to see clearly.

UK - Page 18

Image 18
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsKeep ALL Parts of Your Body away from the saw Safety Apparel Specific Safety RulesGeneral Precautions Basic Precautions in the CUTTING/ Work AreaKICK-BACK Maintenance PrecautionsPush and Pull Pull PushSymbols Symbol Name ExplanationSymbols Specifications Features SAFE-T-TIPANTI-KICK-BACK Nose Guard Understanding Your Chainsaw Safety DevicesOperation LOW KICK-BACK SAW ChainRUN Position Brake KICK-BACK PrecautionsChain Brake KICK-BACK Danger Zone RotationalMixing the Fuel Fuel and RefuellingHandling the Fuel Safely Filling the TankBrake Position Ignition Switch RUN Primer Bulb Adding OILStarting the Engine Starting a Cold Engine Ignition Switch Stop Position Stopping the EngineStarting a Warm Engine Proper Cutting Stance Preparing for CuttingProper Grip on Handles Chain LineAdjusting the Carburettor Basic OPERATING/CUTTING ProceduresWork Area Precautions AIR FilterAdjusting Idling Speed Operating the Chain BrakeBrake Position RUN Position Felling Trees Hazardous Conditions Keep Bystanders AwayRetreat Path Proper Procedure for Tree Felling Planned Line of FallRetreat Hinge Back CUT HingeNotch Approx /3 Diameter Trunk Back CUT WedgeBucking with a Wedge Removing Buttress RootsBucking Vertical CUT Loose Section Horizontal KICK-BACK WedgeUNDER-BUCKING Bucking Logs Under StressOVER-BUCKING LOG Supported AT ONE END Finishing CUTLoad Second CUT Limbing and PruningCutting Spring Poles Finishing CUT Spring PoleMaintenance Assembling the BAR and ChainCutters Chain Tensioning Screw Adjusting the Chain Tension Chain MaintenanceFlats on Drive Links Sharpening the Cutters Check for Wear or Damage LEFT-HAND Cutters RIGHT-HAND Side Plate Angle Maintaining Depth Gauge ClearanceTOP Plate Filing Angle Correct Less thanMaintaining the SAFE-T-TIPNOSE Guard Restore Original Shape by Rounding FrontMaintaining the Guide BAR Lubricating HoleCleaning the AIR Filter Mounting the SAFE-T-TIP Nose GuardTighten 3/4 A Turn Checking the Fuel Filter Cleaning the Starter UnitCleaning the Engine Replacing the Sparking PlugChain Brake Cleaning the Spark Arresting SilencerChain Catcher Brake Band Clean the Chain Brake Storing the Chainsaw 1 Month or LongerTroubleshooting BAR and Chain CombinationsTroubleshooting Warranty Guarantee Statement Rtsa / Rtuk / RTGRyobi Technologies GmbH