Homelite CSP3816, CSP4518 manual Table of Contents, Introduction

Page 2

 

TABLE OF CONTENTS

Introduction

2

General Safety Rules

3-4

Specific Safety Rules

5-6

Symbols

7-8

Specifications

9

Features

10

Operation

11-25

Maintenance

26-36

Bar and Chain Combination

37

Troubleshooting

37-38

Warranty

39

 

INTRODUCTION

IMPORTANT

Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. When servicing use only identical Homelite replacement parts.

For safe operation, read and understand all instructions before using the chainsaw. Follow all safety instructions. Failure to follow all safety instructions listed below may result in serious personal injury.

WARNING:

Carefully read through this entire operator’s manual before using your new saw. Pay close attention to the Safety Rules and all Safety Alert Symbols including Danger, Warning and Caution. These safety rules are for your safety and to prevent possible serious injury. If you use your saw properly and only for what it is intended, you will enjoy years of safe, reliable service.

Look for this symbol to point out important safety precautions. It means attention!!! Your safety is involved.

WARNING:

The operation of any tool can result in foreign objects being thrown into the eyes, which may cause severe eye injury. Before beginning tool operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend Wide Vision Safety Mask for use over glasses or standard safety glasses with side shields. Always wear eye protection.

UK - Page 2

Image 2
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL InstructionsKeep ALL Parts of Your Body away from the saw Safety Apparel Specific Safety RulesGeneral Precautions Basic Precautions in the CUTTING/ Work AreaKICK-BACK Maintenance PrecautionsPush and Pull Pull PushSymbols Symbol Name ExplanationSymbols Specifications Features SAFE-T-TIPANTI-KICK-BACK Nose Guard Understanding Your Chainsaw Safety DevicesOperation LOW KICK-BACK SAW ChainRUN Position Brake KICK-BACK PrecautionsChain Brake KICK-BACK Danger Zone RotationalMixing the Fuel Fuel and RefuellingHandling the Fuel Safely Filling the TankStarting the Engine Brake Position Ignition Switch RUN Primer BulbAdding OIL Starting a Cold Engine Starting a Warm Engine Ignition Switch Stop PositionStopping the Engine Proper Cutting Stance Preparing for CuttingProper Grip on Handles Chain LineAdjusting the Carburettor Basic OPERATING/CUTTING ProceduresWork Area Precautions AIR FilterBrake Position RUN Position Adjusting Idling SpeedOperating the Chain Brake Retreat Path Felling Trees Hazardous ConditionsKeep Bystanders Away Retreat Proper Procedure for Tree FellingPlanned Line of Fall Hinge Back CUT HingeNotch Approx /3 Diameter Trunk Back CUT WedgeBucking with a Wedge Removing Buttress RootsBucking Vertical CUT Loose Section Horizontal KICK-BACK WedgeUNDER-BUCKING Bucking Logs Under StressOVER-BUCKING LOG Supported AT ONE END Finishing CUTLoad Second CUT Limbing and PruningCutting Spring Poles Finishing CUT Spring PoleMaintenance Assembling the BAR and ChainCutters Chain Tensioning Screw Flats on Drive Links Adjusting the Chain TensionChain Maintenance Sharpening the Cutters Check for Wear or Damage LEFT-HAND Cutters RIGHT-HAND Side Plate Angle Maintaining Depth Gauge ClearanceTOP Plate Filing Angle Correct Less thanMaintaining the SAFE-T-TIPNOSE Guard Restore Original Shape by Rounding FrontMaintaining the Guide BAR Lubricating HoleTighten 3/4 A Turn Cleaning the AIR FilterMounting the SAFE-T-TIP Nose Guard Checking the Fuel Filter Cleaning the Starter UnitCleaning the Engine Replacing the Sparking PlugChain Brake Cleaning the Spark Arresting SilencerChain Catcher Brake Band Clean the Chain Brake Storing the Chainsaw 1 Month or LongerTroubleshooting BAR and Chain CombinationsTroubleshooting Warranty Guarantee Statement Rtsa / Rtuk / RTGRyobi Technologies GmbH