Honda Power Equipment RM752A manual Front Corner Baffle Installation figure

Page 12

Front Corner Baffle Installation (figure 2)

Attach front corner baffle (5) up under mower frame as shown and attach with bolts (8) and flange lock- nuts (9).

Ensure both slde skids, the left side shield and elther the dkcharge chute or rlght slde shleid are installed.

Right Side Shield & Baffle Installation

(flgure 2)

FRONT CORNER

INSTALLATION

INSTALLATION

INSTALLATION

1.Mower frame

2. Right side skid

D83052A

 

3.Discharge chute

4.Right side shield

5.Front corner baffle

6.Side shield baffle

7. 3/8 x 1" Bolt

8.3/8 x 3/4" Carriage bolt

9.3/8" Flanged hex locknut

10. 3/8" Lockwasher

11. 3/8" Hex nut

Figure 2. Right Skid, Shield & Discharge Chute

When right side shield (4) is installed, you must

~~

I

install side shield baffle (6). Attach rear portion of

 

baffle (6) to mower frame with bolt (8) and flange

 

 

locknut (9) as shown. Attach front end of baffle (6)

 

 

to side shield (4) with bolt (8) and flange locknut (9)

 

 

as shown. Attach side shield (4) to mower frame

 

 

with bolts (7) and flange locknuts (9) as shown.

 

 

Discharge Chute Installation (figure 2)

The discharge chute (3) may be installed in place of baffle (6) and side shield (4). Attach discharge chute

(3)to right side of mower with bolts (7)and flange locknuts (9) as shown.

Right Side Skid Installation (figure 2)

The right skid (2) also serves as a guard. Do not operate mower unless it is in place and in good condition.

Attach right side skid (2) to mower frame (1) as shown with bolts (7), lockwashers (10) and nuts (11). Do not tighten this hardware as the skid will require adjustment when cutting height is set.

Caster Arm Installation (figure 3)

1.Mower frame

2.Caster arm

3. Adjustment bracket

D m 1A

4.1/2 X 1-1/2" Bolt

5.1/2 x 1-3/4"Carriage bolt

6.1/2" Flanged hex locknut

Figure 3. Caster Arm Installation

10

F-7756 (10-89)

Image 12
Contents Page Page Specifications Table of ContentsIntroduction General Information PRE-DELIVERY Check ListDelivery Check List Daily Check ListOperational Safety TrainingPreparation Safety Rules Maintenance SafetyStorage Safety Decals Replace Immediately If DamagedShield Missing Do not OperateTorque Chart Bolt Head MarkingsRecommended Torque in Foot Pounds Newton-Meters Hardware ABBREVlATlONSAssembly Left Side Skid and Shield InstallationFront Corner Baffle Installation figure Right Side Shield & Baffle InstallationDischarge Chute Installation figure Right Side Skid Installation figureTop Link Pivot Installation figure Check Chain Installation figureDrive Shaft Installation 7756 Operation Cutting Height Adjustment figure Attaching Mower to TractorImportant Notice Tube assembly Removing Mower from TractorPre-Operation Check List Important NoticeOperating Technique Uneven Terrain Owner Service Lubrication Information figureBlade Installation figure Belt Replacement figureBlade Servicing Blade Removal figureCorrect Incorrect Blade Spindle Disassembly figure Blade Spindle Assembly figureSpindle Repair Blade Spindle RemovalApart Blade Spindle Installation Drive Spindle Disassembly figureDrive Spindle Assembly figure Drive Spindle Removal figureDrive Spindle Installation Universal Joint Repair figures 18Assembly 7756 10-89 Trouble Shooting Problem Possible CauseIndex to Parts Lists Main Frame Assembly Mllsaci Mounting Frame Assembly NQ DescriDtion Front Drive & Shield Assembly Rear Drive 8t Shield AssemblyDrive Spindle Assembly CW Blade Spindle AssemblyIndex Dealer Set-Up InstructionsTelephone 404