Harbor Freight Tools 94191 Length of Coverage, No Charge Repair or Replacement, Warranted Parts

Page 25

Emission Control System Warranty - continued

Harbor Freight Tools Emission Control Defects Warranty Provisions

1.Length of Coverage

HFT warrants to a first retail purchaser and each sub- sequent purchaser that the engine is free from defects in materials and workmanship that cause the failure of warranted parts for a period of two (2) years after the date of delivery to the first retail purchaser.

2.No Charge Repair or Replacement

Repair or replacement of any warranted part will be performed at no charge to the owner if the work is performed through a warranty station authorized by HFT. For emissions warranty service, contact the HFT Customer Service Department at 1-800-444-3353.

5.Service and Maintenance

Component parts which are not scheduled for replace- ment as required maintenance or are scheduled only for regular inspection to the effect of “repair or replace as necessary” are warranted for the warranty period. Any warranted part which is scheduled for replace- ment as required maintenance is warranted for the period of time up to the first scheduled replacement point for that part. Any replacement part, provided it is equivalent in durability and performance, may be used in performance of maintenance or repairs. The owner is responsible for commissioning a qualified technician/mechanic to perform all required mainte- nance, as outlined in the Inspection, Cleaning, and Maintenance section on page 17 of this manual.

3.Consequential Damages Coverage

Coverage under this warranty shall also extend to

 

6.

Warranted Parts

the failure of any engine components caused by the

 

 

 

 

 

 

1)

Fuel Metering System

failure of any warranted part while it is still covered

 

 

i)

Carburetor and its internal parts.

under this warranty.

 

 

 

 

ii)

Fuel pump (if so equipped).

 

 

 

 

 

4.

Coverage Exclusions

 

 

iii)

Cold start enrichment system.

2)

Air Induction System

 

 

 

Warranty claims shall be filed in accordance with the

 

 

i)

Intake pipe/manifold.

provisions of the HFT warranty policy explained in the

 

 

 

 

ii)

Air cleaner.

box at the top of the previous page. HFT shall not be

 

 

3)

Ignition System

liable for any loss of use of the engine, for any alter-

native usage, for any damage to goods, loss of time,

 

 

i)

Spark plug.

or inconvenience. Warranty coverage shall also be

 

 

ii)

Magneto ignition system.

excluded for any part which fails, malfunctions, or is

 

 

 

4) Catalyst System (if so equipped)

damaged due to failure to follow the maintenance and

 

 

 

i)

Exhaust pipe stud.

operating instructions set forth in the Owner’s Manual

 

 

 

 

ii)

Muffler.

including, but not limited to:

 

 

(a) use of parts which are not authorized by HFT

 

 

iii)

Catalytic converter (if so equipped).

(b) improper installation, adjustment or repair of the

5)

Miscellaneous items Used in Above Systems

 

engine or of any warranted part unless performed

 

 

i)

Vacuum, temperature and time sensitive

 

by an authorized warranty center

 

 

 

valves and switches.

(c)

failure to follow recommendations on fuel use

 

 

ii)

Hoses, belts, connectors, and assemblies.

 

contained in the Owner’s Manual

 

 

 

 

 

(d)improper or inadequate maintenance of any war- ranted parts

(e)repairs performed outside of the authorized war- ranty service dealers

(f)alterations by changing, adding to or removing parts from the engine.

SKU 94191

For technical questions, please call 1-800-444-3353.

Page 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents For technical questions or replacement parts, please call Your Warranty Is Voided IfGeneral Safety Rules and Precautions SpecificationsSave this Manual Work AreaTool USE and Care Personal SafetySKU For technical questions, please call Service Specific Safety Rules and PrecautionsMechanical Precautions Fire and Explosion PrecautionsChemical Precautions Use only Engine manufacturer recommended fuel and oilElectrical Precautions Noise PrecautionsInsulate all connections and disconnected wires Nameplate Extension Cord Length MISC. Precautions120 or 240 Volt At full loadTo Install The Battery not included Assembly InstructionsUnpacking See Figure BGeneral Location Installation InstructionsGrounding The Generator Control Panel FeaturesSee Figure C See Figure DFigure D To Add Engine Oil PRE-START InstructionsSee Figure E Operating InstructionsSee Figure E To Fill The Fuel Tank See Figure F To Start The Engine/GeneratorTo Connect Electrical Loads See Figure F SKU For technical questions, please call Volts x Amps = Watts example 120 volts x 3 amps = 360 wattsDo not use damaged equipment Generator maintenance INSPECTION, MAINTENANCE, and CleaningSee Figure G Engine maintenanceFuel Tank CAP Fuel Filter Troubleshooting Please Read the Following Carefully Parts List Generator Assembly Diagram Generator Part Description Qty Parts List EngineSKU 94191 For technical questions, please call Assembly Diagram EngineOwner’s Warranty Responsibilities Limited 1 year warrantyService and Maintenance No Charge Repair or ReplacementLength of Coverage Consequential Damages CoverageElectrical Diagram

94191 specifications

Harbor Freight Tools is widely recognized for delivering high-quality tools at affordable prices, and one of the standout products in their lineup is the 94191 6-Inch Bench Grinder. This versatile tool is perfect for both DIY enthusiasts and seasoned professionals alike, providing a powerful solution for sharpening, grinding, and polishing tasks.

One of the main features of the Harbor Freight Tools 94191 is its robust 2.1 amp motor, which provides a reliable power source for various grinding applications. The motor allows the grinder to reach a maximum speed of 3,450 revolutions per minute (RPM), ensuring effective material removal and efficiency. This makes the tool ideal for sharpening blades, shaping metal, or removing rust and corrosion.

The 94191 model features a well-designed cast iron base that provides stability during operation. The vibration-free design contributes to more accurate grinding and enhances safety, reducing the risk of accidents. Additionally, the grinder comes equipped with two grinding wheels: a coarse wheel for quick material removal and a fine wheel for precision sharpening. The dual-wheel setup allows users to switch between different grinding tasks without needing to change tools.

Another great characteristic of the Harbor Freight Tools 94191 is the adjustable eye shields. These shields help protect users' eyes from debris while providing a clear view of their work. The adjustable nature of the shields allows users to position them at various angles, enhancing safety while ensuring visibility during operations.

Additionally, the bench grinder is designed with a built-in work light, which illuminates the workspace and improves visibility, especially in dim lighting conditions. This feature is particularly useful for users needing detailed work while ensuring they maintain consistency and accuracy.

The Harbor Freight Tools 94191 also integrates a maintenance-free design, making it easy to use without requiring extensive upkeep. The inclusion of rubber feet ensures stability during operation and helps absorb vibration, prolonging the tool's lifespan.

In summary, the Harbor Freight Tools 94191 6-Inch Bench Grinder is a powerful, user-friendly tool that combines various features and technologies tailored to meet the needs of any metalworking task. With its robust motor, dual-wheel setup, adjustable eye shields, built-in work light, and durable construction, this bench grinder is an excellent addition to any workshop, whether for professional or personal use.
Top Page Image Contents