Harbor Freight Tools 56088 warranty See Figure E, To Connect Electrical Loads

Page 16

3.To start the Engine manually, using the Starter Handle (41A) and Starter Rope (40A), insert the Ignition Key (65) and turn the Engine Ignition (2) to its “RUN” po- sition. Grasp the Starter Handle (41A) on the Starter Rope (40A) and pull slowly until resistance is felt. Allow the Rope to rewind slowly. Then, pull the Handle with a rapid, full arm stroke. Allow the Rope to rewind slowly. If necessary, repeat this procedure until the Engine starts.

4.When the Engine starts, slowly move the Choke Lever (21A) to its “RUN” position.

(See Figure E.)

5.IMPORTANT: Allow the Generator to run at no load for five minutes after each start-up so that the Engine and Generator can stabilize.

To Connect Electrical Loads:

1.Start the Engine, and allow the Engine and Generator to run and warm up for five minutes after starting with no electrical load.

2.WARNING! Connect 120 VAC appliances, tools, and equipment only to the four 120 VAC Outlets (5). Connect 240 AC appliances, tools, and equipment only to the one 240 VAC Outlet (6). Connect 12 VDC appliances, tools, and equipment only to the 12 VDC Terminal (7). (See Figure C.)

3.CAUTION! Never exceed the rated capacity for this Generator, as serious dam- age to the Generator and/or appliances, tools, and equipment could result from an overload. Starting and running wattage requirements should always be calculated when matching this Generator’s wattage capacity to the appliance, tool, or equip- ment.

4.Most appliances, tools, and equipment will list on the motor nameplate the starting and running voltage and amperage requirements. Use the following formula to convert voltage and amperage to wattage:

Volts x Amps = Watts (example: 120 volts x 3 amps = 360 watts)

5.To determine the approximate wattage requirement for most appliances, tools, and equipment with “inductive” type motors, multiply the wattage that was calculated by 2 times to ensure adequate Generator capacity for motor load starting current.

6.NOTE: The starting and running wattage for “resistant” loads are the same. Ex-

ample: a 100 Watt light bulb requires only 100 Watts to start. Most resistant loads will be listed in wattage.

7.Always power the largest electric motor first. Then, plug in other appliances, tools, and equipment one at a time.

a.Connect “inductive” load appliances, tools, and equipment first. Inductive loads consist of small hand tools and some small appliances. Connect the items that require the most wattage first.

b.Connect any lights next.

SKU 56088

For technical questions, please call 1-800-444-3353.

Page 16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Your Warranty Is Voided If For technical questions or replacement parts, please callSpecifications General Safety Rules and PrecautionsSave this Manual Work AreaPersonal Safety Tool USE and CareAC Applications Specific Safety Rules and Precautions ServiceFire and Explosion Precautions Mechanical PrecautionsChemical Precautions Use only Engine manufacturer recommended fuel and oilElectrical Precautions Noise PrecautionInsulate all connections and disconnected wires MISC. Precautions Nameplate Extension Cord Length120 or 240 Volt At full loadAssembly Instructions To Install The Battery not includedUnpacking See Figure aInstallation Instructions General LocationControl Panel Features Figure C PRE-START Instructions To Add Engine OilSee Figure D To Fill The Fuel Tank This Unit can Power the Following ItemsSee Figure D Operating Instructions To Start The Engine/GeneratorTo Connect Electrical Loads See Figure EVolts x Amps = Watts example 120 volts x 3 amps = 360 watts INSPECTION, MAINTENANCE, and Cleaning Do not use damaged equipment Generator maintenanceEngine maintenance Figure FFuel Tank CAP Fuel Filter Troubleshooting Please Read the Following Carefully Parts List Generator Part Description QtyAssembly Diagram Generator Parts List Engine Assembly Diagram Engine Limited 1 year warranty Owner’s Warranty ResponsibilitiesNo Charge Repair or Replacement Service and MaintenanceLength of Coverage Consequential Damages CoverageElectrical Diagram

56088 specifications

Harbor Freight Tools 56088 is a versatile and cost-effective solution for those in need of reliable hand tools. Renowned for its focus on affordability without sacrificing quality, this product is a prime example of the brand’s commitment to delivering exceptional value.

One of the standout features of the Harbor Freight Tools 56088 is its robust construction. The tool is designed to withstand rigorous use and is made from high-quality materials, ensuring durability and longevity. This makes it an ideal choice for both DIY enthusiasts and professional users who require tools that can handle tough jobs day in and day out.

The 56088 model is equipped with a range of ergonomic features that enhance user comfort and reduce fatigue during prolonged use. Its non-slip grip handle provides stability and control, allowing users to exert maximum force without compromising safety. This is particularly beneficial when performing tasks that require precision.

Another key characteristic of the Harbor Freight Tools 56088 is its ease of use. The design incorporates intuitive features that make it user-friendly, even for those who may be new to hand tools. Instructions are straightforward, and the tool’s functionality is clear, making it accessible to a wide range of users.

In terms of technology, the Harbor Freight Tools 56088 is equipped with innovations that enhance its performance. Precision engineering ensures that the tool operates efficiently, delivering results that meet or exceed user expectations. Additionally, the design incorporates features that promote safety, such as mechanisms to prevent accidental disengagement during use.

The versatility of the Harbor Freight Tools 56088 cannot be understated. It is suitable for various applications, from simple household repairs to more complex tasks. This adaptability makes it a valuable addition to any toolbox, providing users with numerous possibilities for tackling different projects.

Overall, the Harbor Freight Tools 56088 represents a perfect blend of quality, comfort, safety, and versatility. It is crafted for both the seasoned tradesperson and the casual DIYer, ensuring that everyone can achieve professional results with a tool that is both accessible and efficient. With its robust construction and user-focused design, the 56088 is a reliable choice in the realm of hand tools.
Top Page Image Contents