Great Dane GCKH2352S Adjusting Mower Deck Cutting Height, Adjusting Mower Deck Anti-Scalp Wheels

Page 15

OPERATING

4.Push ROPS into upright position.

5.Install drilled pin (B) into holes on left and right side of ROPS, and secure in place with spring pins (A).

6.Check the ROPS bolt torque if the ROPS is loose.

Lowering ROPS

CAUTION: Avoid injury! Use roll-over protection system (ROPS) in lowered position only when low clearance operation is necessary.

•Do not use seat belt when ROPS is in lowered position.

•Do not operate machine on slope with ROPS in folded position.

•Raise ROPS and fasten seat belt as soon as conditions permit.

1.Park machine safely. (See Parking Safely in the SAFETY section). 2.Remove spring pin (A) from drilled pin (B) on left and right side of ROPS. 3.Remove drilled pin from left and right side of ROPS.

4.Pull ROPS rearward to lower.

5.Install drilled pins and spring pins back into hole in ROPS to secure in place.

Adjusting Mower Deck Cutting Height

CAUTION: Avoid injury! Rotating blades are dangerous and can cut fingers and toes. Stop engine, lock the park brake, and wait for blade to stop rotating before adjusting cutting height.

Cutting height can be adjusted from approximately 25-125 mm (1-5 in.). Each hole adjusts the height-of-cut (HOC) in approximately 12 mm (1/2 in.) increments.

The deck can also be raised and locked in a transport position, to provide maximum ground clearance when moving the machine from one area to another.

1.Park machine safely. (See Parking Safely in the SAFETY section.)

2.Move the mower deck lift lever (A) to the transport position (D).

3.Position the HOC adjustment pin (C) in the proper hole for the desired height-of-cut.

4.Pull back and hold the mower deck lift lever (A) and release the transport position lock lever (B).

5.Allow the mower deck lift lever (A) to rest against the HOC adjustment pin (C).

Adjusting Mower Deck Anti-Scalp Wheels

1.Park machine safely. (See Parking Safely in the SAFETY section.)

CAUTION: Avoid injury! Fingers and loose clothing can get caught in rotating parts. Do not operate machine without all mower deck belt shields installed.

NOTE: The flattest cut can be achieved by having all anti-scalp wheels adjusted off the ground. Check anti-scalp wheel adjustments each time the mower deck cutting height is changed.

It is recommended that all anti-scalp wheels be kept off the ground to minimize scuffing.

2.Inflate tires to correct pressure.

3.Adjust mower deck to desired cutting height.

Operating - 13

Page 14 Page 16
Image 15
Page 14 Page 16
Contents OPERATOR’S Manual Page Introduction IntroductionProduct Identification Safety Labels Safety LabelsUnderstanding The Machine Safety Labels Safety Labels Avoid Crushing Safety SafetyUsing a Spark Arrestor Checking Mowing Area Parking SafelyRotating Blades are Dangerous Use Seat Belt Properly Keep Rops Installed ProperlyProtect Children Avoid TippingDriving Safely on Public Roads Maintenance and StorageKeep Riders Off Avoid High Pressure FluidsTire Safety Prevent FiresHandling Fuel Safely Handling Waste Product and Chemicals Daily Operating ChecklistOperating OperatingRaising and Lowering Operator Seat Operator Station ControlsMiscellaneous Controls Mounting and Dismounting Machine SafelyAdjusting Seat Using Seat BeltRaising and Lowering Rops Adjusting Mower Deck Anti-Scalp Wheels Adjusting Mower Deck Cutting HeightTesting Neutral Start Switch Testing Safety SystemsTesting PTO Switch Testing Park Brake SwitchProcedure Testing Seat SwitchTesting the Park Brake Using the Park BrakeUsing the Hourmeter Using the Key SwitchUsing the PTO Using the Throttle LeverDisengage Choke Using the ChokeUsing the Motion Control Levers Engage ChokeGentle Right Turn ForwardReverse Gentle Left TurnStarting the Engine Sharp Left TurnSharp Right Turn Mowing Tips Engaging MowerStopping the Engine Transporting MachineService Intervals Service IntervalsSpray Lubricant Service LubricationService Lubrication GreaseAvoid Fumes Service EngineService Engine Engine Warranty Maintenance StatementChecking Engine Oil Level Changing Engine Oil and FilterOil Capacity With Filter Dry Replacing Fuel Filter Cleaning Engine Air Intake Screen and FanChecking and Cleaning Air Filter Elements Adjusting CarburetorChecking Hydraulic Oil Level Service TransmissionService Transmission Hydraulic OilCleaning Hydraulic Pump Cooling Fins Removing and Installing Traction Drive BeltChecking and Adjusting Motion Control Linkages Neutral Creep Adjustment Maximum Speed Drift AdjustmentCheck Maximum Speed Drift Service Transmission Hydraulic System Hose Routing Service Steering & Brakes Service Steering & BrakesHydraulic System Schematic Servicing Front Caster Wheel Roller Bearings Chariot Removing and Installing Front Caster WheelsAdjusting Front Caster Spindle Bearing InstallingHeight Adjustment Procedure Servicing Caster Spindle BearingsCheck Alignment Removing and Installing Mower Deck Foot Plate Service MowerService Mower Adjusting Park BrakeLeveling Mower Deck Removing and Installing Mower Deck Belt ShieldsAdjusting Level Side-to-Side Picture Note Discharge chute raised for photo clarityChecking Level Front-to-Rear Checking and Adjusting Cutting Height Adjusting Deck Lift Assist Spring TensionChecking and Adjusting Mower Deck Drive Belt Tension Checking and Replacing Mower Blades Removing and Installing Mower Deck Drive BeltReplacing Mower Blades Sharpening BladesBalancing Blades Replacing Mower Spindle BearingsRemoving and Installing the Battery Service ElectricalService Electrical Service the Battery SafelyBurnishing the PTO Clutch Cleaning Battery and TerminalsUsing Booster Battery Replacing FuseWiring Schematic Service Miscellaneous Service MiscellaneousCleaning and Repairing Metal Surfaces TroubleshootingTroubleshooting Cleaning and Repairing Plastic SurfacesEngine Electrical SystemCheck Mower Deck MachinePark Brake SteeringStorage StorageAssembly AssemblySpecifications SpecificationsGetting Quality Service Getting Quality ServiceGetting Quality Service Engine and Related Components B&S 23 HP Vanguard Remarks DescriptionEngine and Related Components B&S 26 HP ELS Ref. No Description Qty Remarks           Engine and Related Components Kawasaki KAI/KOHLER  $,/$     $,/$Locknut Ref. No Description Qty Remarks Fuel Delivery System ComponentsOver the LAP Control Assembly Electrical and Related Components Fuse Console and Control Assembly Console Hydrostatic Drive System Components Ref.No Description Qty Remarks Traction Drive and Brakes Pivot Hydraulic Schematic Seat Standard Chariot Frame Assembly Frame Front Caster Assembly Yoke Caster 200550 RopsPage Spindle Assembly Ref. No Description Qty Remarks Deck Lift Assembly Bearing CAP Cutting Deck Mower Deck 52 & 61 Cutting Deck Description Labels Decal Hydro OIL Specs

GCKA1948S, GCBR2652S, GCKH2352S, GCKH2361S, GCBV2348S specifications

The Great Dane GCBV2361S, GCKA1952S, GCBR2661S, GCKH2348S, and GCBV2348S are remarkable contributions to the world of modern appliances, celebrated for their efficiency, performance, and sleek designs. Each model embodies a commitment to technological excellence, offering a suite of features that cater to the diverse needs of users in kitchens across the globe.

The GCBV2361S is a standout model that combines a stylish stainless steel finish with user-friendly controls. It incorporates advanced cooking technologies, such as convection heating, which ensures uniform cooking by circulating hot air. This model not only enhances flavor but significantly reduces cooking times.

The GCKA1952S presents a compact yet powerful choice, ideal for smaller kitchens without compromising on performance. It features energy-efficient settings perfect for those conscious of their carbon footprint. With a smart digital display, users can easily navigate through various cooking options, while the integrated timer ensures perfect results every time.

For those looking to up their culinary game, the GCBR2661S offers professional-grade features typically found in high-end kitchens. It is equipped with multiple cooking modes, including steam and broil functions, granting users the versatility to experiment with diverse recipes. Its spacious interior and adjustable racks allow for cooking larger meals, making it perfect for family gatherings.

The GCKH2348S transitions seamlessly from multifunctional cooking to elegant serving. This model boasts self-cleaning technology, which helps maintain hygiene without the fuss, and its intuitive interface simplifies the cooking process. Additionally, its aesthetically pleasing design adds a touch of sophistication to any kitchen décor.

Lastly, the GCBV2348S combines style with cutting-edge technology, featuring Wi-Fi connectivity that allows users to control the appliance remotely via smartphone apps. This model supports voice commands for hands-free operation, further enhancing convenience in today’s fast-paced lifestyles.

In conclusion, the Great Dane GCBV2361S, GCKA1952S, GCBR2661S, GCKH2348S, and GCBV2348S represent the pinnacle of modern kitchen technology. With their innovative features, energy efficiency, and sleek designs, these appliance models are ideal for food enthusiasts and casual cooks alike, ensuring excellent results with minimal effort. Each model caters to specific needs and preferences, making them essential tools for any contemporary kitchen.
Top Page Image Contents