Great Dane GCKH2348S, GCBV2361S, GCKA1952S Starting the Engine, Sharp Left Turn, Sharp Right Turn

Page 21

OPERATING

Sharp Left Turn:

•Push right control lever forward and pull left control lever rearward at the same time.

Sharp Right Turn:

4.Push PTO knob (A) down to disengage PTO. 5.Move throttle lever to set engine speed:

•Cold engine: Set throttle lever at the 1/2- to 3/4-throttle position.

•Warm/Hot engine: Set throttle lever to the 1/2-throttle position. 6.Position choke knob (D):

•Cold engine: Pull knob up and hold in choke position.

•Warm/Hot engine: If necessary, pull knob up and hold in choke position.

IMPORTANT: Avoid damage! Starter may be damaged if starter is operated for more than 20 seconds at a time:

• Wait two minutes before trying again if engine does not start.

•Push left control lever forward and pull right control lever rearward at the same time.

Starting the Engine

CAUTION: Avoid injury! Engine exhaust fumes contain carbon monoxide and can cause serious illness or death.

Move the machine to an outside area before running the engine.Do not run an engine in an enclosed area without adequate ventilation.

•Connect a pipe extension to the engine exhaust pipe to direct the exhaust fumes out of the area.

•Allow fresh outside air into the work area to clear the exhaust fumes out.

1.Sit on the operator seat.

2.Lock the park brake.

3.Move both motion control levers to the neutral detent position (standard levers) or neutral lock position (optional “over the lap” levers).

STOP

C

B

7.Turn key switch to start position (B).

If the engine does not start, wait 10 seconds.

•Turn key to start position again for no more than 5 seconds.

•Repeat the procedure if necessary.

IMPORTANT: Avoid damage! Unnecessary engine idling can cause engine overheating, carbon build-up, and poor performance.

8.Release key to run position (C) when engine starts. 9.With engine started:

•Push choke knob to off position.

•Move throttle lever to full-throttle position.

•Unlock the park brake.

Operating - 19

Page 20 Page 22
Image 21
Page 20 Page 22
Contents OPERATOR’S Manual Page Introduction IntroductionProduct Identification Safety Labels Safety LabelsUnderstanding The Machine Safety Labels Safety Labels Avoid Crushing Safety SafetyUsing a Spark Arrestor Checking Mowing Area Parking SafelyRotating Blades are Dangerous Protect Children Keep Rops Installed ProperlyAvoid Tipping Use Seat Belt ProperlyKeep Riders Off Maintenance and StorageAvoid High Pressure Fluids Driving Safely on Public RoadsTire Safety Prevent FiresHandling Fuel Safely Operating Daily Operating ChecklistOperating Handling Waste Product and ChemicalsMiscellaneous Controls Operator Station ControlsMounting and Dismounting Machine Safely Raising and Lowering Operator SeatAdjusting Seat Using Seat BeltRaising and Lowering Rops Adjusting Mower Deck Anti-Scalp Wheels Adjusting Mower Deck Cutting HeightTesting PTO Switch Testing Safety SystemsTesting Park Brake Switch Testing Neutral Start SwitchTesting the Park Brake Testing Seat SwitchUsing the Park Brake ProcedureUsing the PTO Using the Key SwitchUsing the Throttle Lever Using the HourmeterUsing the Motion Control Levers Using the ChokeEngage Choke Disengage ChokeReverse ForwardGentle Left Turn Gentle Right TurnStarting the Engine Sharp Left TurnSharp Right Turn Stopping the Engine Engaging MowerTransporting Machine Mowing TipsService Intervals Service IntervalsService Lubrication Service LubricationGrease Spray LubricantService Engine Service EngineEngine Warranty Maintenance Statement Avoid FumesChecking Engine Oil Level Changing Engine Oil and FilterOil Capacity With Filter Dry Checking and Cleaning Air Filter Elements Cleaning Engine Air Intake Screen and FanAdjusting Carburetor Replacing Fuel FilterService Transmission Service TransmissionHydraulic Oil Checking Hydraulic Oil LevelCleaning Hydraulic Pump Cooling Fins Removing and Installing Traction Drive BeltChecking and Adjusting Motion Control Linkages Neutral Creep Adjustment Maximum Speed Drift AdjustmentCheck Maximum Speed Drift Service Transmission Hydraulic System Hose Routing Service Steering & Brakes Service Steering & BrakesHydraulic System Schematic Adjusting Front Caster Spindle Bearing Removing and Installing Front Caster WheelsInstalling Servicing Front Caster Wheel Roller Bearings ChariotHeight Adjustment Procedure Servicing Caster Spindle BearingsCheck Alignment Service Mower Service MowerAdjusting Park Brake Removing and Installing Mower Deck Foot PlateLeveling Mower Deck Removing and Installing Mower Deck Belt ShieldsAdjusting Level Side-to-Side Picture Note Discharge chute raised for photo clarityChecking Level Front-to-Rear Checking and Adjusting Cutting Height Adjusting Deck Lift Assist Spring TensionChecking and Adjusting Mower Deck Drive Belt Tension Checking and Replacing Mower Blades Removing and Installing Mower Deck Drive BeltBalancing Blades Sharpening BladesReplacing Mower Spindle Bearings Replacing Mower BladesService Electrical Service ElectricalService the Battery Safely Removing and Installing the BatteryUsing Booster Battery Cleaning Battery and TerminalsReplacing Fuse Burnishing the PTO ClutchWiring Schematic Service Miscellaneous Service MiscellaneousTroubleshooting TroubleshootingCleaning and Repairing Plastic Surfaces Cleaning and Repairing Metal SurfacesEngine Electrical SystemCheck Park Brake MachineSteering Mower DeckStorage StorageAssembly AssemblySpecifications SpecificationsGetting Quality Service Getting Quality ServiceGetting Quality Service Engine and Related Components B&S 23 HP Vanguard Remarks DescriptionEngine and Related Components B&S 26 HP ELS Ref. No Description Qty Remarks   $,/$ Engine and Related Components Kawasaki KAI/KOHLER    $,/$          Locknut Ref. No Description Qty Remarks Fuel Delivery System ComponentsOver the LAP Control Assembly Electrical and Related Components Fuse Console and Control Assembly Console Hydrostatic Drive System Components Ref.No Description Qty Remarks Traction Drive and Brakes Pivot Hydraulic Schematic Seat Standard Chariot Frame Assembly Frame Front Caster Assembly Yoke Caster 200550 RopsPage Spindle Assembly Ref. No Description Qty Remarks Deck Lift Assembly Bearing CAP Cutting Deck Mower Deck 52 & 61 Cutting Deck Description Labels Decal Hydro OIL Specs

GCKA1948S, GCBR2652S, GCKH2352S, GCKH2361S, GCBV2348S specifications

The Great Dane GCBV2361S, GCKA1952S, GCBR2661S, GCKH2348S, and GCBV2348S are remarkable contributions to the world of modern appliances, celebrated for their efficiency, performance, and sleek designs. Each model embodies a commitment to technological excellence, offering a suite of features that cater to the diverse needs of users in kitchens across the globe.

The GCBV2361S is a standout model that combines a stylish stainless steel finish with user-friendly controls. It incorporates advanced cooking technologies, such as convection heating, which ensures uniform cooking by circulating hot air. This model not only enhances flavor but significantly reduces cooking times.

The GCKA1952S presents a compact yet powerful choice, ideal for smaller kitchens without compromising on performance. It features energy-efficient settings perfect for those conscious of their carbon footprint. With a smart digital display, users can easily navigate through various cooking options, while the integrated timer ensures perfect results every time.

For those looking to up their culinary game, the GCBR2661S offers professional-grade features typically found in high-end kitchens. It is equipped with multiple cooking modes, including steam and broil functions, granting users the versatility to experiment with diverse recipes. Its spacious interior and adjustable racks allow for cooking larger meals, making it perfect for family gatherings.

The GCKH2348S transitions seamlessly from multifunctional cooking to elegant serving. This model boasts self-cleaning technology, which helps maintain hygiene without the fuss, and its intuitive interface simplifies the cooking process. Additionally, its aesthetically pleasing design adds a touch of sophistication to any kitchen décor.

Lastly, the GCBV2348S combines style with cutting-edge technology, featuring Wi-Fi connectivity that allows users to control the appliance remotely via smartphone apps. This model supports voice commands for hands-free operation, further enhancing convenience in today’s fast-paced lifestyles.

In conclusion, the Great Dane GCBV2361S, GCKA1952S, GCBR2661S, GCKH2348S, and GCBV2348S represent the pinnacle of modern kitchen technology. With their innovative features, energy efficiency, and sleek designs, these appliance models are ideal for food enthusiasts and casual cooks alike, ensuring excellent results with minimal effort. Each model caters to specific needs and preferences, making them essential tools for any contemporary kitchen.
Top Page Image Contents