Great Dane GCBV2361S, GCKA1952S manual Service Mower, Adjusting Park Brake, Alignment Procedure

Page 36

SERVICE MOWER

To mount in the high position, mount the levers to the top four holes in the mounting bracket.

To mount in the low position, mount the levers to the bottom four holes in the mounting bracket.

Checking and Aligning Motion Control Levers - Optional Over the Lap Levers

Check Alignment:

1.Park machine safely. (See Parking Safely in the SAFETY section.)

2.Move both motion control levers (A) from the neutral lock to the neutral steer position.

3.Check levers for equal alignment.

Check gap (B) between the levers. The recommended gap is 3-6 mm (1/8-1/4 in.).

NOTE: If the ends of the levers strike against each other while in the neutral position, move the levers to the neutral lock position and carefully bend them outward. Move them back to the neutral position and check for the recommended gap of 3-6 mm (1/8-1/4 in.).

If positions of the control levers are unequal, an adjustment is necessary.

Alignment Procedure

1.Adjust position of motion control levers:

Loosen cap screws (C).

Slide both levers forward or rearward to desired position on control arm until levers are aligned.

Tighten cap screws.

Adjusting Park Brake

IMPORTANT: Avoid damage! Due to initial brake wear, the park brake should be checked and adjusted after the first 25 hours of use.

A park brake that is adjusted too tightly could damage the transmission or cause premature brake wear.

1.Park machine safely. (See Parking Safely in the SAFETY section.)

2.Loosen set screw (A).

3.Turn knob (B) clockwise several times.

4.Tighten set screw down in the lower slot. 5.Test park brake.

Service Mower

Removing and Installing Mower Deck Foot Plate

CAUTION: Avoid injury! Always operate the mower with the foot plate installed. Operating with the foot plate removed can cause serious injury.

Service Mower - 34

Image 36
Contents OPERATOR’S Manual Page Introduction IntroductionProduct Identification Safety Labels Safety LabelsUnderstanding The Machine Safety Labels Safety Labels Avoid Crushing Safety SafetyUsing a Spark Arrestor Checking Mowing Area Parking SafelyRotating Blades are Dangerous Keep Rops Installed Properly Protect ChildrenAvoid Tipping Use Seat Belt ProperlyMaintenance and Storage Keep Riders OffAvoid High Pressure Fluids Driving Safely on Public RoadsTire Safety Prevent FiresHandling Fuel Safely Daily Operating Checklist OperatingOperating Handling Waste Product and ChemicalsOperator Station Controls Miscellaneous ControlsMounting and Dismounting Machine Safely Raising and Lowering Operator SeatAdjusting Seat Using Seat BeltRaising and Lowering Rops Adjusting Mower Deck Cutting Height Adjusting Mower Deck Anti-Scalp WheelsTesting Safety Systems Testing PTO SwitchTesting Park Brake Switch Testing Neutral Start SwitchTesting Seat Switch Testing the Park BrakeUsing the Park Brake ProcedureUsing the Key Switch Using the PTOUsing the Throttle Lever Using the HourmeterUsing the Choke Using the Motion Control LeversEngage Choke Disengage ChokeForward ReverseGentle Left Turn Gentle Right TurnStarting the Engine Sharp Left TurnSharp Right Turn Engaging Mower Stopping the EngineTransporting Machine Mowing TipsService Intervals Service IntervalsService Lubrication Service LubricationGrease Spray LubricantService Engine Service EngineEngine Warranty Maintenance Statement Avoid FumesChecking Engine Oil Level Changing Engine Oil and FilterOil Capacity With Filter Dry Cleaning Engine Air Intake Screen and Fan Checking and Cleaning Air Filter ElementsAdjusting Carburetor Replacing Fuel FilterService Transmission Service TransmissionHydraulic Oil Checking Hydraulic Oil LevelCleaning Hydraulic Pump Cooling Fins Removing and Installing Traction Drive BeltChecking and Adjusting Motion Control Linkages Neutral Creep Adjustment Maximum Speed Drift AdjustmentCheck Maximum Speed Drift Service Transmission Hydraulic System Hose Routing Service Steering & Brakes Service Steering & BrakesHydraulic System Schematic Removing and Installing Front Caster Wheels Adjusting Front Caster Spindle BearingInstalling Servicing Front Caster Wheel Roller Bearings ChariotHeight Adjustment Procedure Servicing Caster Spindle BearingsCheck Alignment Service Mower Service MowerAdjusting Park Brake Removing and Installing Mower Deck Foot PlateRemoving and Installing Mower Deck Belt Shields Leveling Mower DeckAdjusting Level Side-to-Side Picture Note Discharge chute raised for photo clarityChecking Level Front-to-Rear Checking and Adjusting Cutting Height Adjusting Deck Lift Assist Spring TensionChecking and Adjusting Mower Deck Drive Belt Tension Removing and Installing Mower Deck Drive Belt Checking and Replacing Mower BladesSharpening Blades Balancing BladesReplacing Mower Spindle Bearings Replacing Mower BladesService Electrical Service ElectricalService the Battery Safely Removing and Installing the BatteryCleaning Battery and Terminals Using Booster BatteryReplacing Fuse Burnishing the PTO ClutchWiring Schematic Service Miscellaneous Service MiscellaneousTroubleshooting TroubleshootingCleaning and Repairing Plastic Surfaces Cleaning and Repairing Metal SurfacesEngine Electrical SystemCheck Machine Park BrakeSteering Mower DeckStorage StorageAssembly AssemblySpecifications SpecificationsGetting Quality Service Getting Quality ServiceGetting Quality Service Engine and Related Components B&S 23 HP Vanguard Description RemarksEngine and Related Components B&S 26 HP ELS Ref. No Description Qty Remarks Engine and Related Components Kawasaki KAI/KOHLER   $,/$    $,/$          Locknut Fuel Delivery System Components Ref. No Description Qty RemarksOver the LAP Control Assembly Electrical and Related Components Fuse Console and Control Assembly Console Hydrostatic Drive System Components Ref.No Description Qty Remarks Traction Drive and Brakes Pivot Hydraulic Schematic Seat Standard Chariot Frame Assembly Frame Front Caster Assembly Yoke Caster Rops 200550Page Spindle Assembly Ref. No Description Qty Remarks Deck Lift Assembly Bearing CAP Cutting Deck Mower Deck 52 & 61 Cutting Deck Description Labels Decal Hydro OIL Specs

GCKA1948S, GCBR2652S, GCKH2352S, GCKH2361S, GCBV2348S specifications

The Great Dane GCBV2361S, GCKA1952S, GCBR2661S, GCKH2348S, and GCBV2348S are remarkable contributions to the world of modern appliances, celebrated for their efficiency, performance, and sleek designs. Each model embodies a commitment to technological excellence, offering a suite of features that cater to the diverse needs of users in kitchens across the globe.

The GCBV2361S is a standout model that combines a stylish stainless steel finish with user-friendly controls. It incorporates advanced cooking technologies, such as convection heating, which ensures uniform cooking by circulating hot air. This model not only enhances flavor but significantly reduces cooking times.

The GCKA1952S presents a compact yet powerful choice, ideal for smaller kitchens without compromising on performance. It features energy-efficient settings perfect for those conscious of their carbon footprint. With a smart digital display, users can easily navigate through various cooking options, while the integrated timer ensures perfect results every time.

For those looking to up their culinary game, the GCBR2661S offers professional-grade features typically found in high-end kitchens. It is equipped with multiple cooking modes, including steam and broil functions, granting users the versatility to experiment with diverse recipes. Its spacious interior and adjustable racks allow for cooking larger meals, making it perfect for family gatherings.

The GCKH2348S transitions seamlessly from multifunctional cooking to elegant serving. This model boasts self-cleaning technology, which helps maintain hygiene without the fuss, and its intuitive interface simplifies the cooking process. Additionally, its aesthetically pleasing design adds a touch of sophistication to any kitchen décor.

Lastly, the GCBV2348S combines style with cutting-edge technology, featuring Wi-Fi connectivity that allows users to control the appliance remotely via smartphone apps. This model supports voice commands for hands-free operation, further enhancing convenience in today’s fast-paced lifestyles.

In conclusion, the Great Dane GCBV2361S, GCKA1952S, GCBR2661S, GCKH2348S, and GCBV2348S represent the pinnacle of modern kitchen technology. With their innovative features, energy efficiency, and sleek designs, these appliance models are ideal for food enthusiasts and casual cooks alike, ensuring excellent results with minimal effort. Each model caters to specific needs and preferences, making them essential tools for any contemporary kitchen.