Torque Specifications | Generac Power Systems manual

Section 2 — Installation

Guardian Liquid-cooled 15 kW, 20 kW and 25 kW Generators

NOTE:

1.16 BEFORE INSTALLATION

Port 1 is for NG only and Port 2 is for LP vapor only. No provision for simultaneous fuels has been made.

DANGER

Serious injury or damage may occur if not con-

!figured properly. Please consult an authorized Generac Service Dealer with any questions.

1.13 TORQUE SPECIFICATIONS

Cylinder Head	15 (+ 90° + 90°) ft.lb.
Intake Manifold	13 ft.lb.
Exhaust Manifold	13 ft.lb.

1.14 ENGINE OIL RECOMMENDATIONS

The unit has been filled with 15W-40 engine oil at the factory. Use a high-quality detergent oil classified “For Service CC, SD, SE, SF.” Detergent oils keep the engine cleaner and reduce carbon deposits. Use oil having the following SAE viscosity rating, based on the ambient temperature range anticipated before the next oil change:

	Temperature			Oil Grade (Recommended)
	Above 80° F (27° C)			SAE 30W or 15W-40
	32° to 80° F (-1° to 27° C)			SAE 20W-20 or 15W-40
	Below 32° F (0° C)			SAE 10W or 15W-40

Any attempt to crank or start the engine before

!it has been properly serviced with the recom- mended oil may result in an engine failure.

1.15 COOLANT RECOMMENDATIONS

Use a mixture of half low silicate ethylene glycol base anti-freeze and deionized water. Cooling system capacity is about 8 U.S. quarts (7.6 liters). Use only deionized water and only low silicate anti-freeze. If desired, add a high quality rust inhibitor to the rec- ommended coolant mixture. When adding coolant, always add the recommended 50-50 mixture.

Do not use any chromate base rust inhibitor

!with ethylene glycol base anti-freeze or chromi- umhydroxide (“green slime”) forms and will cause overheating. Engines that have been operated with a chromate base rust inhibitor must be chemically cleaned before adding eth- ylene glycol base anti-freeze. Using any high silicate anti-freeze boosters or additives will also cause overheating. Generac Power Systems also recommends that any soluble oil inhibitor is NOT used for this equipment.

Before installing this equipment, check the ratings of both the generator and the transfer switch. Read “Emergency Isolation Method” and “Total Circuit Isolation Method” in Sections 2.5 and 2.6.

The generator’s rated wattage/amperage capacity must be adequate to handle all electrical loads that the unit will power. The critical (essential) loads may need to be grouped together and wired into a sepa- rate “emergency” distribution panel.

This generator can be installed in conjunction with a standard Generac “GTS” type transfer switch, if desired.

The standard transfer switch has no sensing or con- trolling circuit boards. Instead, the generator control console houses a “Printed Circuit Board Assembly”, which controls all phases of operation, including engine start up and load transfer.

2.1STANDBY GENERATOR INSTALLATION

DANGER

Connecting this generator to an electrical sys- tem normally supplied by an electric utility shall be by means of a transfer switch, so as to isolate the electric system from the utility distribution system when the generator is operating. Failure to isolate the electric sys- tem by these means will result in damage to the generator and may also result in injury or death to utility workers due to backfeed of electrical energy.

If an open bottom is used, the engine-genera- tor is to be installed over non-combustible materials and should be located such that com- bustible materials are not capable of accumu- lating under the generator set.

Only qualified, competent installation contractors or electricians thoroughly familiar with applicable codes, standards and regulations should install this standby electric power system. The installation must comply strictly with all codes, standards and regula- tions pertaining to the installation.

This genset must be installed on a level surface. The base frame must be level within 1/2 inch all around.

After the system has been installed, do nothing

!that might render the installation in noncompli- ance with such codes, standards and regula- tions.

8 Generac® Power Systems, Inc.

004721-0, 004722-0, 004723-0, 004724-0, 004725-0, 004725-1, 004725-2, 004725-3, 004726-0 specifications

Generac Power Systems is a leader in energy solutions, committed to providing reliable power products for homes, businesses, and industrial applications. Among their extensive range of products, the Generac Power Systems models 004721-0, 004722-0, 004723-0, 004724-0, 004725-0, 004725-1, 004725-2, 004725-3, and 004726-0 stand out due to their advanced features and innovative technologies.

One of the key features of these models is the robust engine performance. They are designed with Generac's signature engines, which ensure optimal power output and durability. This leads to better energy efficiency while maintaining a low operating cost. The models are engineered for seamless operation under various load conditions, ensuring that you stay powered in any situation.

These Generac models also incorporate state-of-the-art transfer switch technology, which enhances their reliability. The transfer switches ensure that power is instantly transferred from the grid to the generator during an outage, allowing for uninterrupted service. This is especially critical for homes and businesses where power reliability is essential.

Combining convenience with efficiency, the models feature user-friendly interfaces that simplify operation. With available mobile monitoring options, users can keep track of their power status and diagnostics remotely. This is a game changer for individuals who want to maintain oversight of their energy solutions without being physically present.

Safety is another critical aspect integrated into the Generac Power Systems. The models are equipped with advanced safety features such as overload protection, low oil shutdown, and high-temperature shutdown, ensuring an added layer of security for users.

Moreover, these models are built with rugged construction materials making them suitable for all environmental conditions. Whether it’s extreme cold or heat, they are crafted to withstand the elements while performing at peak efficiency.

Generac Power Systems emphasizes sustainability as well, with models designed for lower emissions and quieter operation. This is ideal for homeowners and businesses conscious of their environmental impact and seeking to reduce noise pollution.

Overall, the Generac Power Systems models 004721-0, 004722-0, 004723-0, 004724-0, 004725-0, 004725-1, 004725-2, 004725-3, and 004726-0 represent the evolution of power generation technology. With their robust features, efficient operation, and commitment to safety, these generators are an excellent investment for anyone seeking reliable power solutions.