Generac Power Systems 004988-4 Plate AIR Cleaner Adapter, Adapter Carburetor W/PVC Conn

Page 47

Section 9 - Exploded Views and Parts

Liquid-cooled 30 kW Generators

Air Cleaner — Drawing No. 0F6850-A

1

2

3

4

5

6

7

8

9

ITEM

PART NO.

QTY.

DESCRIPTION

1

0E5193

1

PLATE AIR CLEANER ADAPTER

2

0E0519A

1

ADAPTER CARBURETOR W/PVC CONN

3

049226

4

WASHER LOCK M5

4

049815

4

SCREW HHC M5-0.8 X 16 G8.8

5

0C8127

1

ELEMENT AIR CLEANER

6

022127

1

NUT HEX 1/4-20 STEEL

7

062974

1

STUD TH 1/4-20 X 4-1/2 G2 ZNC

8

0A5547

1

COVER - AIR CLEANER

9

037561

1

NUT WING 1/4-20 NYLK

45

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Liquid-cooled, Prepackaged Standby Generators Introduction Authorized Service Dealer Location‹ Operation and Maintenance ‹ HOW to Obtain ServiceTable of Contents  Warning   Electrical Hazards  Generator AC Connection Systems Transfer SwitchGenerator Automatic System OperationLOW OIL Presure Switch LOW Coolant Level Switch ‹ 1.7.2 High Coolant Temperature Switch‹ 1.7.1 LOW OIL Pressure Switch ‹ 1.7.3 LOW Coolant Level SwitchLifting the Generator Unpacking‹ 1.10.2 Engine Specifications SpecificationsReconfiguring the Fuel System ‹ 1.10.1 Generator SpecificationsEngine OIL Recommendations Torque SpecificationsStandby Generator Installation Before Installation‹ 2.1.2 Other Published Standards Generator Mounting SupportBasic Standby Electric System Grounding the Generator Transfer Switch Signal ConnectionsEmergency Circuit Isolation Method Total Circuit Isolation Method‹ 2.9.2 GTS-TYPE ATS Battery InstallationPreparation Before START-UP Using AN Engineered GTS Transfer Switch Control Console Components ‹ 3.2.1 AUTO/OFF/MANUAL Switch‹ 3.2.2 Fault Indicator LED ‹ 3.2.5 SET Exercise Time SwitchAutomatic Operation AdjustmentsManual Transfer START-UP Engine Governor Retransfer and ShutdownCooling System Weekly Exercise CycleChecking Fluid Levels Overload Protection for Engine DC Electrical System‹ 4.5.10 Changing Engine OIL ‹ 4.5.11 Changing the Engine AIR Cleaner‹ 4.5.8 Check FAN Belt ‹ 4.5.9 Inspect Engine Governor‹ 4.5.13 Coolant Change Miscellaneous Maintenance‹ 4.6.3 Battery Maintenance ‹ 4.6.1 Cleaning the Generator‹ Periodic Replacement Parts ‹ 4.6.4 Battery ReplacementService Maintenance Interval Information Scheduled MaintenanceLevel Maintenance Level Problem Cause Correction Troubleshooting PointsLiquid-cooled 30 kW Generators Installation Diagram Size AWG Transfer SwitchAUTO/OFF/MANUAL Switch SET Exerciser SwitchOn PCB Otherwise Noted AS ShownBAT Ignition CoilDPE SWITCH, AUTO/OFF/MANUALSWITCH, SET Exerciser Starter Motor GOV 12V Battery REDALT DEGEngine Foot Hold Down Battery Boot Battery CableBattery Post Cover Baclk Battery Post Cover RED +To a To B Plcs Duct Discharge LH Front Assy Wire 14AWG 7.5 #0 GRN/YELIntake Duct HSB Duct Discharge RH FrontPage Cover Front Panel HSB Assy 2A 12V UL BatteryControl BOX HSB Decal AVR CoverCooled 30 kW Drawing No Exploded Bracket DC ALT 3.0L Ford Wire SET 3.0L Ford notNot SHOWN-USED to Hold OIL Drain Assembly Coil Ignition 3.0L FordFrame Side Support Radiator HSB Tank Coolant RecoveryRadiator R-IN,L-OUT Venturi 3.0L Ford HSBTo B Washer Flat 5/16 Zinc Weldment Mounting BaseFlange Fuel Inlet Assy Regulator 3.0L NG or LPVLocktight Rotor 39030AD1 HSB Tecum Rotor 390 15KW 1P Direct HSB 2.5L FordRotor 390 20KW 1P Direct HSB 2.5L Ford Rotor 390 25KW 1P Direct HSB 2.5L FordGasket Exhaust Ring Exhaust Flange 2 PipePipe Muffler OUT Washer Lock 3/8 SSAdapter Carburetor W/PVC Conn Plate AIR Cleaner AdapterElement AIR Cleaner Cover AIR CleanerWarranty Schedule
Top Page Image Contents