Dynasty Spas D-1000 Circulation Pump optional, Blower optional, Fiber Optic Light optional

Page 17

To p S i d e C o n t r o l I n s t r u c t i o n s

Circulation Pump (optional)

When the water is at set temperature or below, the circulation pump (if installed) runs 24 hours a day. However, it turns off a 2 F above set temperature and comes back on for 1 hour every 3 hours until it reaches set temperature again.

Blower (optional)

Press the pad once to turn the blower on high. Press a second time, blower is on low speed. Press a third time to turn off. The blower will automatically turn itself off after 20 minutes.

Light

Press the pad to turn the spa light on and off. The light will automat- ically turn off after 1 hour.

Fiber Optic Light (optional)

Press the LIGHT pad once for the light and the color wheel, again for the light to pause on one color, and again to turn the light completely off. The light will automatically turn itself off after 1 hour

Standard and Economy Mode

Press the pad to switch between standard and economy mode. Economy mode only heats the water during filter cycles. Standard mode maintains the desired temperature at all times. We suggest using the standard mode.

Panel Lock

Press the pad then JETS 1. The panel will be locked, and the LED will show LOC alternately with the water temperature. All automatic

functions will continue to operate. To unlock the panel, push then JETS 1 again

Preset Filter Cycles

Your spa will automatically filter itself twice each day. The first filter cycle begins 1 minute after the spa is energized. The second filter cycle will begin 12 hours after the start of the first filter cycle. Filter duration is programm- able at the topside panel for FILO, FIL1, FIL2, FIL3 FIL4 or filc - 24 hours. The default filter setting is 2 hours. To program, press the WARM or COOL

pad then the pad. Press the WARM or COOL pad to select the filter time duration. Press the MODE pad again to exit the programming sequence. During filtration, the low-speed pump will run and the blower operates for 30 seconds at the start of the first filter cycle to clean out the air channel.

The heater will also run during filter cycles. An ozone generator (if installed) will run 24 hours/day.

Auxiliary Panel (optional)

The jets and blower (if installed) can also be activated from an auxiliary panel. The operation is the same as described for the main panel.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Page Dealer InstallerDyynnaassttyy SSppaass Ownneerrss Maannuuaall Dear Dynasty Spa Owner P o r t a n t S a f e t y I n s t r u c t i o n s SPA & Pool Institute S i c I n t r o d u c t o r y I n f o r m a t i o n T u p & D e l i v e r y G u i d e l i n e s T u p & D e l i v e r y G u i d e l i n e s R i n g D i a g r a m Factory Recommended G.F.C.I Load Center WiringN e r a l P r e O p e r a t i o n I n s t r u c t i o n s To p S i d e C o n t r o l I n s t r u c t i o n s Freeze Protection Preset Filter CyclesDiagnostic Messages Preset Filter Cycles Auxiliary Panel optional System auxiliary panel optional Circulation Pump optional Standard and Economy ModeBlower optional LightEconomy StandardFlow IceMini Diverter Valve Dual Filter Lt e r L o c a t i o nSingle Filter Lt e r M a i n t e n a n c e Cleaning and Replacing Filter CartridgeFilling Spa With Water Cleaning Your Spa WaterBalance Water TestingAs Needed An Overview Monthly For Equipment ProtectionAlgae Control An Overview As NeededSkin Conditioning A i n i n g Yo u r S p a N t e r i z i n g Yo u r S p a Winterize Your SPAN t e r i z i n g S p a C o v e r s Ask Your Dealer About Using a Cover CaddyPump will not prime Spa Lights wont come onJets wont come on No heat or heat too lowSpa is leaking Low water flowMotor does not run Motor runs hotAir Blower Air Loop Air Venturi Cabinet O s s a r y o f T e r m sSkimmer O s s a r y o f T e r m s c o n tA M o d e l s D e t a i l R e f e r e n c e C h a r t
Top Page Image Contents