Echo PPT-280 specifications Long Term Storage Over 30 Days

Page 33

PPT-280

STORAGE

 

 

STORAGE

During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result.

Long Term Storage (Over 30 Days)

Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following:

1. Store unit in a dry, dust free place, out of the reach of children.

Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark.

2.Place the stop switch in the “OFF” position.

3.Remove accumulation of grease, oil, dirt and debris from exterior of unit.

Some tree sap and resins are corrosive. Thoroughly wash the guide bar and sprocket areas after each use, then coat metal parts with light oil

4.Perform all periodic lubrication and services that are required.

5.Tighten all the screws and nuts.

6.Drain fuel tank completely. Press purge bulb 6 -7 times to remove remaining fuel from carburetor then drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel.

7.

a.Allow engine to cool then remove the spark plug and pour 7 cc (1/4 oz.) of fresh, clean, two-stroke engine oil into the cylinder through the spark plug hole.

b.Pull the recoil starter handle 2-3 times to distribute the oil inside the engine.

c.Observe the piston location through the spark plug hole. Pull the recoil handle slowly until the piston reaches the top of its travel and leave it there.

8.Install the spark plug (do not connect ignition cable).

9.Install the sprocket guard on the guide bar and saw chain during storage.

X7702091009

33

© 02/2014 ECHO Inc.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Burn Hazard Operator’s ManualTable of Contents Introduction Servicing InformationIntroduction Safety SafetyAdditional or Replacement Manuals Manual Safety Symbols and Important InformationMixture International SymbolsPersonal Condition and Safety Equipment Repetitive Stress Injuries Vibration and ColdClear the Work Area Read the ManualsUse Proper Clothing & Equipment Keep a Firm GripKickback EquipmentGuide Bar and Saw Chain Emission Control Exhaust & Evaporative Emission Control Exhaust & EvaporativeEPA 2010 and Later and/or C.A.R.B. Tier Product Emission Durability Emission Compliance PeriodDescription Description Contents Assembly AssemblyDrive Shaft/Handle Assembly Drive Shaft/Power HeadAssembly Cutting Attachment to Drive Shaft InstallationTo Adjust Saw Chain Tension Saw Chain Tension AdjustmentOperation OperationFuel Fuel RequirementsAfter use Handling FuelAdjusting Automatic Oiler Lubricating the Guide Bar and Saw ChainAutomatic Oiling System Purge Bulb Starting Cold EngineStopping Engine Starting Warm EnginePruning Techniques Maintenance MaintenanceMaintenance Intervals Skill LevelsFuel Filter Air FilterCooling System Spark PlugSpark Arrestor Screen Exhaust SystemExhaust Port Cleaning Carburetor AdjustmentEngine Break-In High Altitude OperationMAINTENANCEPPT-280 LubricationFlexible Drive Shaft Guide Bar and Saw Chain Replacement Guide Bar Replacement / InstallationSprocket Guard Cleaning BAR P/N Chain P/N Chain Type Links Pitch Guage Filing Standard Saw ChainTop Plate Angle Troubleshooting TroubleshootingStorage StorageLong Term Storage Over 30 Days Specifications SpecificationsOWNER’S Responsibility Warranty StatementsPurchased Repair PARTS, Short Blocks and Accessories Warranty StatementsPPT-280 PPT-280 PPT-280 ECHO, Incorporated
Top Page Image Contents