Dixon ZTR 5424, ZTR 5020 manual Care and Maintenance

Page 33

CARE AND MAINTENANCE

MOWER DECK INSTALLATION:

1.Loosen and remove front body mounting bolts (P/N 3368) and washers (P/N 3066). Disconnect headlight wiring plug from wiring harness. Lift front body from chassis.

2.Install rear hanger rods on lift frame. Slide lift plate on hanger rods, small holes in lift plate will face rear of mower, and start nylok nuts on each hanger rod until approximately 1/2 inch of threads are exposed.

3.Position mower deck under chassis.

4.Raise front of mower deck and slide front support rod through lift frame and tabs on mower deck. Install hair pin clips on front and rear of support rods.

5.Move lift lever to lowest cut position, install engine to mower deck drive belt on top center pulley. Check belt routing after installation to make certain that belt is centered in groove of electric clutch pulley.

6.Move lift lever toward high cut position and remove brake link from hole on lift lever.

7.Install front body, connect headlight wiring.

Page 31

Image 33
Contents Page Important Read Carefully Index Most common causes of injury to the operator or bystander Safety Alert Symbol Safety SymbolsSerious injury or death Do not Slope OperationBe alert to avoid accidents Service Dixon Limited Warranty Policy -- Estate Models Model ZTR SpecificationsRear 20 X 1 0.5 X 8 Multi Trac Seat Adjustment Instructions Page Parking Brake ControlsTo SET Parking Brake HYDRO-GEAR Drive SystemTo GO Backward To GO ForwardTurning BrakingBlade Drive Circuit BreakerMower Deck CUT Height Lift Lever Before Operating Mower Operation InstructionsBlade Drive Switch Test Starting Instructions Cold Engine Always turn engine off when leaving mower Mowing with a Mulching Attachment Maintain Sharp Blades Throughout The Cutting Season Mowing with a Grass Catcher AttachmentGrass Height Suggestions Side Discharge of the ClippingsDeckrollers Maintenance Schedule Care and MaintenanceCutter Blade Maintenance Belt Tension Lubrication Fuel Shut OFF ValveSeries Rear Wheels Protect Your Investment Changing the Engine OILMower Deck Installation Care and Maintenance Mower Deck Leveling Procedure BOX to Hydrostat Belt Adjustment Parking Brake Cable Adjustment Neutraladjustment Care and Maintenance Ohms Test Procedure for Electric Clutch AdjustmentOIL Filter P/N 5565 Important Hydrostatic Transmission OIL and Filter ServiceWheels and Tires Estate Model 42 Deck Standard Service Parts ListBriggs and Stratton AIR and OIL Filter Part Numbers Troubleshooting Mower CUT QualitySituation Causes Remedy Drive System Situation Causes Remedy Side or the otherElectrical System Purchased from Owner Information

ZTR 5424, ZTR 5020 specifications

The Dixon ZTR 5424 and ZTR 5020 are prominent models in the world of zero-turn mowers, known for their reliability, cutting efficiency, and user-friendly features. These mowers are designed for both residential and commercial use, providing exceptional maneuverability and performance.

The Dixon ZTR 5424 is equipped with a powerful 24-horsepower engine, offering robust performance and ample power for cutting through tough grass and uneven terrain. With its wide 54-inch cutting deck, this model allows for efficient mowing over large areas, minimizing the time required to complete yard work. The deck is crafted with heavy-duty materials to ensure durability, while the adjustable cutting height makes it versatile for different grass types and seasons.

On the other hand, the ZTR 5020 features a slightly smaller engine, typically around 20 horsepower, making it ideal for residential users with medium-sized yards. The 50-inch cutting deck strikes a balance between capability and maneuverability, allowing users to navigate tight corners and landscaping features with ease. Both models utilize a dual-blade design, which enhances cutting efficiency and improves grass discharge, ensuring a well-manicured lawn.

One of the standout technologies found in both models is the hydrostatic transmission, providing smooth acceleration and seamless speed adjustments. This technology allows operators to control the mower with precision while eliminating the need for shifting gears, making mowing more enjoyable. Additionally, the zero-turn design allows for the impressive turning radius, enabling users to make sharp turns around obstacles without leaving uncut patches.

User comfort is also a priority in the design of both mowers. Equipped with ergonomic seats that reduce fatigue during extended use, the ZTR 5424 and ZTR 5020 ensure a comfortable riding experience. Easy-to-reach controls, including adjustable steering levers and intuitive dashboard features, enhance operational ease.

In summary, both the Dixon ZTR 5424 and ZTR 5020 provide powerful performance, efficient cutting capabilities, and user-friendly features. Whether for commercial or residential use, these mowers are well-suited to meet the demands of various mowing environments. With their combination of technology, comfort, and durability, the Dixon ZTR series continues to be a popular choice among lawn care professionals and homeowners alike.