Dixon D26BH54, 434722 To USE Cruise Control J See Fig, To Adjust Mower Cutting Height See Figs

Page 11

OPERATION

K

J

L

Fig. 7

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Figs. 8 and 9)

The position of the attachment lift indicator (W) determines the cutting height.

A

Fig. 8

•Adjust mower to the desired cutting height by pressing the electric lift switch (A) in either the up or down direction.

T

W

Fig. 9

•Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.

CAUTION: Continuing to press the electric lift switch after the mower deck has reached the minimum or maximum position may result in damage to the electric lift mechanism.The elec- tric lift mechanism is equipped with a thermal protection system. If the system overheats or fails to operate, allow the system to cool before attempting to operate again.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

TO ADJUST GAUGE WHEELS (See Fig. 10)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents D26BH54 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly ToremovetractorfromcartonChecklist Operation Reverse Operation System ROS on Know Your TractorHOW to USE Your Tractor To USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigsTo Adjust Gauge Wheels See Fig System CharacteristicsTo Transport See Fig To Stop Mower BladesReverse Operation System ROS To Operate on HillsADD Gasoline Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission Mowing TipsSchedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig SET Parking Brake Lever and Lower AT- Tachment Lift See Fig Service and AdjustmentsTo Install Mower and Drive Belt See Figs To Remove Mower See FigSlide Mower Under Tractor See Fig ANTI-SWAY BAR STurn Steering Wheel Left and Position Mower See Fig Attach Front Link E See Fig Install Belt on Engine Clutch Pulley M SeeAttach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigTo Level Mower To Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Check BrakeTransmission Engine OIL StorageOther Fuel SystemProblem Cause Correction TroubleshootingEngine continues To run when operBattery will not Fires when turnSuggested Guide for Sighting Slopes for Safe Operation Limited Warranty

D26BH54, 434722 specifications

The Dixon D26BH54,434722 is an advanced piece of technology that stands out in the realm of its application. This versatile product has been designed to offer both functionality and efficiency, catering to a diverse range of industries and users. Key features of the Dixon D26BH54 include its robust construction and ergonomic design, ensuring durability and ease of use in various work environments.

One primary characteristic of the D26BH54 is its innovative blend of materials, which allows it to withstand harsh conditions while maintaining a lightweight profile. This is particularly crucial for users who rely on mobility and adaptability in their tasks. The product is also engineered with cutting-edge technology that enhances performance and optimizes energy consumption, making it not only effective but also environmentally friendly.

In terms of functionality, the Dixon D26BH54 is equipped with a range of advanced features that simplify operations. Users can benefit from an intuitive interface that allows for easy navigation and quick adjustments, ultimately improving workflow efficiency. This model integrates smart technology, enabling it to collect and analyze data in real-time, which in turn aids in decision-making processes and operational enhancements.

Furthermore, the D26BH54’s compatibility with various accessories and attachments broadens its utility. This modularity ensures that users can tailor the product to meet their specific needs, adding to its overall versatility. The ability to incorporate additional features as required makes it particularly appealing for businesses looking to adapt to changing demands.

Safety is another critical consideration in the design of the Dixon D26BH54. It incorporates various safety mechanisms and features, ensuring user protection and minimizing potential risks during operation. The inclusion of ergonomic components also promotes user comfort, reducing the likelihood of injury and allowing for extended use without fatigue.

In summary, the Dixon D26BH54,434722 is not just a product but a comprehensive solution designed to enhance efficiency and performance across various applications. With its robust features, integration of smart technology, and focus on safety and user comfort, it is poised to meet the evolving needs of its users, making it a valuable asset in any professional toolkit.
Top Page Image Contents