Dixon 434722, D26BH54 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 26

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANT TO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTURE WHICH LEADS TO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVER TRACTOR WHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents D26BH54 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Toremovetractorfromcarton AssemblyTools Required for Assembly Before Removing Tractor from SkidChecklist Operation Know Your Tractor Reverse Operation System ROS onHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigsTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigTo Operate on Hills To Stop Mower BladesReverse Operation System ROS To Transport See FigCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolineMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower and Drive Belt See Figs SET Parking Brake Lever and Lower AT- Tachment Lift See FigSlide Mower Under Tractor See Fig ANTI-SWAY BAR STurn Steering Wheel Left and Position Mower See Fig Attach Rear Lift Links C See Fig Install Belt on Engine Clutch Pulley M SeeAttach Mower Side Suspension Arms a to Chassis See Fig Attach Front Link E See FigTo Level Mower To Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Check Brake To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionFires when turn To run when operBattery will not Engine continuesSuggested Guide for Sighting Slopes for Safe Operation Limited Warranty

D26BH54, 434722 specifications

The Dixon D26BH54,434722 is an advanced piece of technology that stands out in the realm of its application. This versatile product has been designed to offer both functionality and efficiency, catering to a diverse range of industries and users. Key features of the Dixon D26BH54 include its robust construction and ergonomic design, ensuring durability and ease of use in various work environments.

One primary characteristic of the D26BH54 is its innovative blend of materials, which allows it to withstand harsh conditions while maintaining a lightweight profile. This is particularly crucial for users who rely on mobility and adaptability in their tasks. The product is also engineered with cutting-edge technology that enhances performance and optimizes energy consumption, making it not only effective but also environmentally friendly.

In terms of functionality, the Dixon D26BH54 is equipped with a range of advanced features that simplify operations. Users can benefit from an intuitive interface that allows for easy navigation and quick adjustments, ultimately improving workflow efficiency. This model integrates smart technology, enabling it to collect and analyze data in real-time, which in turn aids in decision-making processes and operational enhancements.

Furthermore, the D26BH54’s compatibility with various accessories and attachments broadens its utility. This modularity ensures that users can tailor the product to meet their specific needs, adding to its overall versatility. The ability to incorporate additional features as required makes it particularly appealing for businesses looking to adapt to changing demands.

Safety is another critical consideration in the design of the Dixon D26BH54. It incorporates various safety mechanisms and features, ensuring user protection and minimizing potential risks during operation. The inclusion of ergonomic components also promotes user comfort, reducing the likelihood of injury and allowing for extended use without fatigue.

In summary, the Dixon D26BH54,434722 is not just a product but a comprehensive solution designed to enhance efficiency and performance across various applications. With its robust features, integration of smart technology, and focus on safety and user comfort, it is poised to meet the evolving needs of its users, making it a valuable asset in any professional toolkit.
Top Page Image Contents