Dixon D26BH54, 434722 manual Troubleshooting, Problem Cause Correction

Page 27

TROUBLESHOOTING

PROBLEM

CAUSE

CORRECTION

Will not start

1.

Out of fuel.

1.

Fill fuel tank.

 

2.

Engine not “CHOKED” properly.

2.

See “TO START ENGINE” in Operation section.

 

3.

Engine flooded.

3.

Wait several minutes before attempting to start.

 

4.

Bad spark plug.

4.

Replace spark plug.

 

5.

Dirty air filter.

5.

Clean/replace air filter.

 

6.

Dirty fuel filter.

6.

Replace fuel filter.

 

7.

Water in fuel.

7.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

8.

Loose or damaged wiring.

8.

Check all wiring.

 

9.

Carburetor out of adjustment.

9.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

10.

Engine valves out of adjustment.

10.

Contact an authorized service center/department.

 

 

 

 

 

Hard to start

1.

Dirty air filter.

1.

Clean/replace air filter.

 

2.

Bad spark plug.

2.

Replace spark plug.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Dirty fuel filter.

4.

Replace fuel filter.

 

5.

Stale or dirty fuel.

5.

Empty fuel tank and refill tank with fresh, clean gas.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Carburetor out of adjustment.

7.

See “To Adjust Carburetor” in Service Adjustments

 

 

 

 

section.

 

8.

Engine valves out of adjustment.

8.

Contact an authorized service center/department.

 

 

 

 

 

Engine will not

1.

Brake pedal not depressed.

1.

Depress brake pedal.

turn over

2.

Attachment clutch is engaged.

2.

Disengage attachment clutch.

 

3.

Weak or dead battery.

3.

Recharge or replace battery.

 

4.

Blown fuse.

4.

Replace fuse.

 

5.

Corroded battery terminals.

5.

Clean battery terminals.

 

6.

Loose or damaged wiring.

6.

Check all wiring.

 

7.

Faulty ignition switch.

7.

Check/replace ignition switch.

 

8.

Faulty solenoid or starter.

8.

Check/replace solenoid or starter.

 

9.

Faulty operator presence switch(es).

9.

Contact an authorized service center/department.

 

 

 

 

 

Engine clicks but

1.

Weak or dead battery.

1.

Recharge or replace battery.

will not start

2.

Corroded battery terminals.

2.

Clean battery terminals.

 

3.

Loose or damaged wiring.

3.

Check all wiring.

 

4.

Faulty solenoid or starter.

4.

Check/replace solenoid or starter.

 

 

 

 

 

Loss of power

1.

Cutting too much grass/too fast.

1.

Raise cutting height/reduce speed.

 

2.

Throttle in “CHOKE” position.

2.

Adjust throttle control.

 

3.

Build-up of grass, leaves, trash under mower.

3. Clean underside of mower housing.

 

4.

Dirty air filter.

4.

Clean/replace air filter.

 

5.

Low oil level/dirty oil.

5.

Check oil level/change oil.

 

6.

Faulty spark plug.

6.

Clean and regap or change spark plug.

 

7.

Dirty fuel filter.

7.

Replace fuel filter.

 

8.

Stale or dirty fuel.

8.

Empty fuel tank and refill tank with fresh, clean gas.

 

9.

Water in fuel.

9.

Empty fuel tank and carburetor, refill tank with fresh

 

 

 

 

gasoline and replace fuel filter.

 

10.

Spark plug wire loose.

10.

Connect and tighten spark plug wire.

 

11.

Dirty engine air screen/fins.

11.

Clean engine air screen/fins.

 

12.

Dirty/clogged muffler.

12.

Clean/replace muffler.

 

13.

Loose or damaged wiring.

13.

Check all wiring.

 

14.

Carburetor out of adjustment.

14.

See “To Adjust Carburetor” in Service Adjustments

 

15.

Engine valves out of adjustment.

15.

Contact an authorized service center/department.

 

 

 

 

 

Excessive

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

vibration

2.

Bent blade mandrel.

2.

Replace blade mandrel.

 

3.

Loose/damaged part(s).

3.

Tighten loose part(s). Replace damaged parts.

 

 

 

 

 

27

Image 27
Contents D26BH54 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Unassembled Parts Before Removing Tractor from Skid AssemblyTools Required for Assembly ToremovetractorfromcartonChecklist Operation Reverse Operation System ROS on Know Your TractorHOW to USE Your Tractor To USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigsTo Adjust Gauge Wheels See Fig System CharacteristicsTo Transport See Fig To Stop Mower BladesReverse Operation System ROS To Operate on HillsADD Gasoline Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission Mowing TipsSchedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Cleaning IN-LINE Fuel Filter See FigDeck Washout Port See Fig SET Parking Brake Lever and Lower AT- Tachment Lift See Fig Service and AdjustmentsTo Install Mower and Drive Belt See Figs To Remove Mower See FigANTI-SWAY BAR S Turn Steering Wheel Left and Position Mower See FigSlide Mower Under Tractor See Fig Attach Front Link E See Fig Install Belt on Engine Clutch Pulley M SeeAttach Mower Side Suspension Arms a to Chassis See Fig Attach Rear Lift Links C See FigTo Level Mower To Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Check BrakeTransmission Engine OIL StorageOther Fuel SystemProblem Cause Correction TroubleshootingEngine continues To run when operBattery will not Fires when turnSuggested Guide for Sighting Slopes for Safe Operation Limited Warranty

D26BH54, 434722 specifications

The Dixon D26BH54,434722 is an advanced piece of technology that stands out in the realm of its application. This versatile product has been designed to offer both functionality and efficiency, catering to a diverse range of industries and users. Key features of the Dixon D26BH54 include its robust construction and ergonomic design, ensuring durability and ease of use in various work environments.

One primary characteristic of the D26BH54 is its innovative blend of materials, which allows it to withstand harsh conditions while maintaining a lightweight profile. This is particularly crucial for users who rely on mobility and adaptability in their tasks. The product is also engineered with cutting-edge technology that enhances performance and optimizes energy consumption, making it not only effective but also environmentally friendly.

In terms of functionality, the Dixon D26BH54 is equipped with a range of advanced features that simplify operations. Users can benefit from an intuitive interface that allows for easy navigation and quick adjustments, ultimately improving workflow efficiency. This model integrates smart technology, enabling it to collect and analyze data in real-time, which in turn aids in decision-making processes and operational enhancements.

Furthermore, the D26BH54’s compatibility with various accessories and attachments broadens its utility. This modularity ensures that users can tailor the product to meet their specific needs, adding to its overall versatility. The ability to incorporate additional features as required makes it particularly appealing for businesses looking to adapt to changing demands.

Safety is another critical consideration in the design of the Dixon D26BH54. It incorporates various safety mechanisms and features, ensuring user protection and minimizing potential risks during operation. The inclusion of ergonomic components also promotes user comfort, reducing the likelihood of injury and allowing for extended use without fatigue.

In summary, the Dixon D26BH54,434722 is not just a product but a comprehensive solution designed to enhance efficiency and performance across various applications. With its robust features, integration of smart technology, and focus on safety and user comfort, it is poised to meet the evolving needs of its users, making it a valuable asset in any professional toolkit.