Dixon 434722, D26BH54 manual To Level Mower

Page 22

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 33)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

NOTE: As desired, you can raise the low side of mower or lower the high side.

•Go to side of mower you wish to adjust.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower the mower, or, to the right to raise the mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

Fig. 33

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 34)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

Fig. 34

•If adjustment is necessary, see steps in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 35 & 36) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position any blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

BB

Fig. 35

•If front tip of blade is not 1/8" to 1/2" lower than the rear tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (tighten) to raise the front of mow- er,or,counterclockwise(loosen)tolowerthefrontmower.

B

A

TIGHTEN ADJUST

LOOSEN

ADJUST NUT

NUT B TO RAISE

B TO LOWER

MOWER

 

02950

MOWER

 

LOOSEN JAM NUT A FIRST

 

Fig. 36

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents D26BH54 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Toremovetractorfromcarton AssemblyTools Required for Assembly Before Removing Tractor from SkidChecklist Operation Know Your Tractor Reverse Operation System ROS onHOW to USE Your Tractor System Characteristics To Adjust Mower Cutting Height See FigsTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigTo Operate on Hills To Stop Mower BladesReverse Operation System ROS To Transport See FigCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolineMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower and Drive Belt See Figs SET Parking Brake Lever and Lower AT- Tachment Lift See FigTurn Steering Wheel Left and Position Mower See Fig ANTI-SWAY BAR SSlide Mower Under Tractor See Fig Attach Rear Lift Links C See Fig Install Belt on Engine Clutch Pulley M SeeAttach Mower Side Suspension Arms a to Chassis See Fig Attach Front Link E See FigTo Level Mower To Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Check Brake To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionFires when turn To run when operBattery will not Engine continuesSuggested Guide for Sighting Slopes for Safe Operation Limited Warranty

D26BH54, 434722 specifications

The Dixon D26BH54,434722 is an advanced piece of technology that stands out in the realm of its application. This versatile product has been designed to offer both functionality and efficiency, catering to a diverse range of industries and users. Key features of the Dixon D26BH54 include its robust construction and ergonomic design, ensuring durability and ease of use in various work environments.

One primary characteristic of the D26BH54 is its innovative blend of materials, which allows it to withstand harsh conditions while maintaining a lightweight profile. This is particularly crucial for users who rely on mobility and adaptability in their tasks. The product is also engineered with cutting-edge technology that enhances performance and optimizes energy consumption, making it not only effective but also environmentally friendly.

In terms of functionality, the Dixon D26BH54 is equipped with a range of advanced features that simplify operations. Users can benefit from an intuitive interface that allows for easy navigation and quick adjustments, ultimately improving workflow efficiency. This model integrates smart technology, enabling it to collect and analyze data in real-time, which in turn aids in decision-making processes and operational enhancements.

Furthermore, the D26BH54’s compatibility with various accessories and attachments broadens its utility. This modularity ensures that users can tailor the product to meet their specific needs, adding to its overall versatility. The ability to incorporate additional features as required makes it particularly appealing for businesses looking to adapt to changing demands.

Safety is another critical consideration in the design of the Dixon D26BH54. It incorporates various safety mechanisms and features, ensuring user protection and minimizing potential risks during operation. The inclusion of ergonomic components also promotes user comfort, reducing the likelihood of injury and allowing for extended use without fatigue.

In summary, the Dixon D26BH54,434722 is not just a product but a comprehensive solution designed to enhance efficiency and performance across various applications. With its robust features, integration of smart technology, and focus on safety and user comfort, it is poised to meet the evolving needs of its users, making it a valuable asset in any professional toolkit.
Top Page Image Contents