Chicago Electric 95283 warranty INSPECTION, MAINTENANCE, and Cleaning

Page 15

7.Before storing the Polesaw/Pruner, make sure to install the Guard Bar Cover

(78) onto the Guard Bar (73). Drain all fuel out of the tool’s Fuel Tank (78A). If this is not followed, old fuel in the Fuel Tank may clog the Carburetor and prevent the tool from starting until cleaned out. Then store the tool in a clean, dry, safe location out of reach of children and other unauthorized people. (See Figure B.)

INSPECTION, MAINTENANCE, AND CLEANING

1. WARNING! Always make sure the Engine’s Power Switch (10) is in its “OFF” position and the Spark Plug (55A) is removed prior to performing any

service, maintenance, or cleaning of the Polesaw/Pruner. (See Figure B.)

2.Before each use: Inspect the general condition of the Polesaw/Pruner. Check misalignment or binding of moving parts, cracked or broken parts, dull or damaged Saw Chain (74) or Guard Bar (73), and any other condition that may affect the safe operation of the tool. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment.

3.Saw Chain (74) maintenance: A dull, improperly sharpened, or damaged Saw Chain can cause kickback, leading to possible personal injury. It is recommended that only a qualified service technician attempt to sharpen or replace the Saw Chain.

4.Spark Plug (55A) maintenance: The condition of the Spark Plug should be checked every six months or 100 hours of tool use. If necessary, clean or replace the Spark Plug.

5.Air Filter (42A) maintenance: The Air Filter should be checked prior to each use of the Polesaw/Pruner for excessive dirt and debris build-up. Thereafter, the Air Filter should be cleaned or replaced every three months or 50 hours of tool use.

6.Drive Gear (44) maintenance: The Drive Gear assembly should be filled, through the Gear Box Grease Fitting (50), with clean, new, automotive axle grease every three months or 50 hours of tool use.

7.To install a replacement Chain: Turn the Chain Tension Adjusting Screw (39) counterclockwise to release tension. Using the accessory Hex Wrench (83), unscrew and remove the Nut (75) that secures the Chain Saw Cover (77) to the unit. The Guard Bar (73) contains a Guard Bar stud slot that fits over the Guard Bar stud. The Guard Bar also has two chain tensioning pin holes which fit over the chain tensioning pins. Place the Guard Bar onto the bar stud so that the chain tensioning pins fit into the chain tensioning pin holes. Fit the Chain over

SKU 95283 For technical questions, please call 1-800-444-3353 PAGE 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Your Warranty Is Voided If GAS Powered POLESAW/PRUNERWork Area Product SpecificationsGeneral Safety Rules and Precautions Save this ManualSKU For technical questions, please call Personal SafetyIMPORTANT! Your Warranty is voided if Specific Safety Rules and PrecautionsKickback Precautions Electrical Precautions Carbon Monixide PrecautionsFire and Explosion Precautions Use only Engine manufacturer recommended fuel and oil Mechanical PrecautionsChemical Precautions Noise PrecautionsAssembly Instructions MISC. Precautions UnpackingSee Figure B Product FeaturesSee Figure B To Fill The Chain Oil Tank PRE-START InstructionsTo Fill The Fuel Tank Operating InstructionsTo Stop The Polesaw/Pruner Figure D INSPECTION, MAINTENANCE, and Cleaning Figure C Please Read the Following Carefully TroubleshootingDescription Parts List POLESAW/PRUNER UnitHex Wrenches not shown Assembly Diagram POLESAW/PRUNER UnitDescription Parts List EngineAssembly Diagram -ENGINE Emission Control System Warranty Warranted Parts Warranty

95283 specifications

The Chicago Electric 95283 is a versatile and robust tool that has gained a reputation for its performance and reliability among DIY enthusiasts and professional tradespeople alike. This compact bench top band saw is designed to handle a variety of cutting tasks, making it a valuable addition to any workshop or home garage.

One of the standout features of the Chicago Electric 95283 is its powerful motor. Equipped with a 1.5 horsepower motor, this band saw delivers strong cutting performance, allowing users to effortlessly cut through various materials including wood, plastic, and even soft metals. The motor operates quietly, which enhances the user experience during long cutting sessions.

In terms of design, the Chicago Electric 95283 boasts a sturdy, all-steel construction that ensures durability and stability. The frame is designed to minimize vibrations, which enhances precision during operation. The saw table is spacious and can be adjusted to an angle for accurate bevel cuts, allowing users to perform more complex cutting tasks with ease.

The band saw features a user-friendly blade tracking adjustment knob, which helps maintain the tension and alignment of the blade. This tool is compatible with a variety of blade widths, enabling users to choose the best blade for their specific cutting needs. The saw also includes a blade guard, ensuring user safety while operating the tool.

Another significant characteristic of the Chicago Electric 95283 is its portability. Despite its robust construction, the band saw is relatively lightweight, making it easy to move around the workshop or take on job sites. This feature is particularly beneficial for contractors who require mobility without compromising on power.

In summary, the Chicago Electric 95283 stands out for its combination of power, precision, and portability. Whether tackling woodworking projects or metalworking tasks, this versatile band saw offers the performance needed to achieve professional-quality results. Its durable construction, user-friendly features, and adjustable capabilities make it an excellent choice for both novices and experienced craftsmen. As the DIY community continues to grow, tools like the Chicago Electric 95283 will play a crucial role in empowering individuals to bring their creative visions to life.
Top Page Image Contents