Rhythm
Press the RHYTHM switch (the LED will light) and the rhythm will begin playing. Use value knob 1 to select the rhythm pattern (50 types), use value knob 2 to adjust the tempo (range:
To stop the rhythm, press the RHYTHM switch while the rhythm is playing.
The rhythm will stop when you enter Bypass, Mute, or Edit modes.
AUX IN
Sound from an audio device (e.g. CD or MD) connected to the AUX IN jack can be mixed with the effect sound for listening, which is a convenient way to practice along with a song.
The AUX input and the effect output will automatically be mixed and output from the OUT PUT jack except when you are in Phrase Trainer mode.
Use the controls on your audio device to adjust the AUX IN volume.
Expression pedal
You can use the expression pedal to control 23 types of Pedal effect in realtime.
If a program uses a Pedal effect, the pedal indicator LED’s will light to indicate the
Using the expression pedal as you play
1.In Program mode, select a program that uses the expression pedal.
2.Make sure that the pedal indicator is lit. If it is not lit, advance the expression pedal once as far as it will go, making the top pedal indicator light (the pedal will be on)
3.Operate the expression pedal while playing your guitar. As you raise and lower the pedal, the output sound will change correspondingly.
If VOLUME is selected in the Pedal effect, it will not be possible to turn the expression pedal on/off. The pedal indicator will re- main lit.
The on/off status of the expression pedal is not memorized by each program.
Do not apply excessive force to the expression pedal. Before oper- ating the expression pedal, verify the amount of force that is re- quired to make the pedal indicator light and to apply the effect.
Effect Select mode
In this mode, you can press the DOWN switch to switch the drive channel while you perform. You can press the UP switch to turn the Modulation and Ambience effects on/off.
As in Program mode, you can edit the settings, use the metro- nome, and write a program.
In this mode it is not possible to switch programs or to select bypass or mute.
Press and hold until |
|
| |
the number LED blinks | Bank down | Bank up | |
Program mode | Program | Program | |
down | up | ||
| |||
Press the Effect Select |
|
| |
key to switch modes |
|
| |
| Switch the | Turn the | |
Effect | drive channel | MOD/AMB | |
| effects on/off | ||
Select mode |
| ||
|
|
Entering Effect Select mode
In Program mode, press the PROG/FX SELECT switch to enter Effect Select mode. The 
."
Switching the drive amp channel
Since each program contains two separate Drive Amp effect set- tings, you can switch between backing and solo sounds without changing programs.
Each time you press the DOWN switch, the Drive Amp effect settings will switch between channels A and B. When channel A is selected the LED beside the DRIVE·AMP switch will light green, and when channel B is selected the LED will light red.
Turning the Modulation and Ambience effects on/off
(INDIVIDUAL)
Each time you press the UP switch, the Modulation effect or Ambience effect will be turned on/off.
The effects that are turned on/off when you press the UP switch can be specified beforehand in the settings of the program, as follows.
Procedure
1.Press the NR LEV switch.
2.Rotate value knob 3 to change the indication in the
MOD: Only the Modulation effect will be turned on/off
AMB: Only the Ambience effect will be turned on/off
M+A: Both the modulation and ambience effects will be turned on/off
For some effects, it is not possible for the Modulation and Pedal effects or the Pedal and Ambience effects to be used simulta- neously. For such combinations, attempting to turn on both ef- fects will cause the
Exiting Effect Select mode
To return to Program mode, press either the PROG/FX SELECT switch or the EXIT switch.
2. Playing the AX100G
7