Bush Hog 300 manual S3PT-02

Page 11
(SBL-4)
(SBL-2)
(SBL-1)
(SG-29)

SAFETY

Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat with the seat belt securely fastened around you. Inadvertent movement of the Tractor or Implement may cause serious injury or death.

Be particularly careful when transporting the Implement with the Tractor. Turn curves or go up hills only at a low speed and using a gradual steering angle. Rear mounted implements move the center of gravity to the rear and remove weight from the front wheels. Make certain, by adding front ballast, that at least 20% of the tractor’s weight is on the front wheels to prevent rearing up, loss of steering control or Tractor tip-over. Slow down on rough or uneven surfaces to prevent loss of steering control which could result in property damage or possible injury. Do not transport unless 3-Point lift lever is fully raised and in the latched transport position. Dropping implement in transport can cause serious damage to the tractor and/or Implement and possibly cause the operator or others to be injured or killed.

(S3PT-02)

Relieve hydraulic pressure prior to doing any maintenance or repair work on the Implement. Place the Implement on the ground or securely blocked up, disengage the PTO, and turn off the tractor engine. Push and pull the Remote Cylinder lever in and out several times prior to starting any maintenance or repair work. (S3PT-09)

This Implement may be wider than the Tractor. Be careful when operating or transporting this equipment to prevent the Implement from running into or striking sign posts, guard rails, concrete abutments or other solid objects. Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control, serious injury, or even death. Never allow the Implement to contact obstacles. (S3PT-12)

There are obvious and hidden potential hazards in operating Rear Blades and Box Scrapers as in all power-driven equipment. REMEMBER! This machine is often operated in rough terrain conditions that include gullies, holes, slopes, hidden obstructions and the like. Serious injury or even death may occur unless care is taken to assure the personal safety of the operator and bystanders in the area.

NEVER PARK BLADE ON THE BACK OF THE MOLDBOARD. Inadvertent falling could cause serious injury or even death. ALWAYS LOWER HITCH onto stand or onto secure blocks.

Never leave blade unattended in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with subsequent injury or death by crushing. Lower Stand and pin in place, or put a secure support under the A-Frame. Lower Blade carefully to the ground. Do not put hands or feet under lifted components.

SAFETY

300 Series 09/10

Safety Section 1-7

© 2010 Alamo Group Inc.

Image 11
Contents Rear Mounted Blade SeriesTo the Owner/Operator/Dealer Table of Contents Page Safety Section Safety Messages SafetySeries 09/10 Safety Section Safety Safety Safety S3PT-02 See Your Bush HOG Dealer Decal Location QTY Level Description Decal Description Safety Logo Product Name Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionIntroduction Before Operating this Machine Assembly Section Assembly of Moldboard to Mainframe AssemblyAssembly Skid Shoes & Quick Tack End Plates Extra Equipment Gauge Wheel Extra EquipmentHydraulic System Hydraulic Control Valve Accessory EquipmentSelector Valve Accessory Equipment Operation Section Operation OperationStandard Equipment and Specifications Personal Protective Equipment PPE Operator RequirementsRops and Seat Belt Tractor HorsepowerTractor Requirements Tractor 3-Point Hitch Front End WeightGetting on and OFF the Tractor Dismounting the Tractor Boarding the TractorStarting the Tractor Connecting the Rear Blade Connecting the Rear Blade to the TractorTractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBlade Pre-Operation Inspection/Service Do not Operate an Unsafe Tractor or Implement Tractor PRE-OPERATION Inspection Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Blade Operating the Tractor and ImplementDitching V-Type Ditch Operating the BladeShutting Down the Implement Disconnecting the Blade from the TractorTransporting the Tractor and Implement Blade StorageTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Problem Possible Cause Remedy Troubleshooting GuideOperation Page Maintenance Section Lubrication MaintenanceProper Torque For Fasteners  Limited WarrantyTo the OWNER/OPERATOR/DEALER Series Rear Mounted Blade