Bush Hog 300 manual Federal Laws and Regulations

Page 19

SAFETY

Federal Laws and Regulations

This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such.

Employer-Employee Operator Regulations

U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA

This Act Seeks:

“...to assure so far as possible every working man and woman in the nation safe and healthful working conditions and to preserve our human resources...”

DUTIES

Sec. 5 (a) Each employer-

(1)shall furnish to each of his employees employment and a place of employment which are free from recognized hazards that are causing or are likely to cause death or serious physical harm to his employees;

(2)shall comply with occupational safety and health standards promulgated under this Act.

(b)Each employee shall comply with occupational safety and health standards and all rules, regulations and orders issued pursuant to this Act which are applicable to his own actions and conduct.

OSHA Training Requirements

Title 29, Code of Federal Regulations Part 1928.57(a)(6). www.osha.gov

Operator instructions. At the time of initial assignment and at least annually thereafter, the employer shall instruct every employee who operates an agricultural tractor and implements in the safe operating practices and servicing of equipment with which they are or will be involved, and of any other practices dictated by the work environment.

Keep all guards in place when the machine is in operation; Permit no riders on equipment

Stop engine, disconnect the power source, and wait for all machine movement to stop before servicing, adjusting, cleaning or unclogging the equipment, except where the machine must be running to be properly serviced or maintained, in which case the employer shall instruct employees as to all steps and procedures which are necessary to safely service or maintain the equipment.

Make sure everyone is clear of machinery before starting the engine, engaging power, or operating the machine.

Employer Responsibilities:

To ensure employee safety during Tractor and Implement operation, it is the employer’s responsibility to:

1.Train the employee in the proper and safe operation of the Tractor and Implement.

2.Require that the employee read and fully understand the Tractor and Implement Operator’s manual.

3.Permit only qualified and properly trained employees to operate the Tractor and Implement.

4.Maintain the Tractor and Implement in a safe operational condition and maintain all shields and guards on the equipment.

5.Ensure the Tractor is equipped with a functional ROPS and seat belt and require that the employee operator securely fasten the safety belt and operate with the ROPS in the raised position at all times.

6.Forbid the employee operator to carry additional riders on the Tractor or Implement.

7.Provide the required tools to maintain the Tractor and Implement in a good safe working condition and provide the necessary support devices to secure the equipment safely while performing repairs and service.

8.Require that the employee operator stop operation if bystanders or passersby come within 25 feet.

Child Labor Under 16 Years of Age

Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.)

SAFETY

300 Series 09/10

Safety Section 1-15

© 2010 Alamo Group Inc.

Image 19
Contents Rear Mounted Blade SeriesTo the Owner/Operator/Dealer Table of Contents Page Safety Section Safety Messages SafetySeries 09/10 Safety Section Safety Safety Safety S3PT-02 See Your Bush HOG Dealer Decal Location QTY Level Description Decal Description Safety Logo Product Name Safety Federal Laws and Regulations Page Introduction Section Introduction IntroductionIntroduction Before Operating this Machine Assembly Section Assembly of Moldboard to Mainframe AssemblyAssembly Skid Shoes & Quick Tack End Plates Extra Equipment Gauge Wheel Extra EquipmentHydraulic System Hydraulic Control Valve Accessory EquipmentSelector Valve Accessory Equipment Operation Section Operation OperationStandard Equipment and Specifications Personal Protective Equipment PPE Operator RequirementsTractor Requirements Tractor HorsepowerRops and Seat Belt Getting on and OFF the Tractor Front End WeightTractor 3-Point Hitch Dismounting the Tractor Boarding the TractorStarting the Tractor Connecting the Rear Blade Connecting the Rear Blade to the TractorTractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBlade Pre-Operation Inspection/Service Do not Operate an Unsafe Tractor or Implement Tractor PRE-OPERATION Inspection Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Blade Operating the Tractor and ImplementDitching V-Type Ditch Operating the BladeShutting Down the Implement Disconnecting the Blade from the TractorTransporting the Tractor and Implement Blade StorageTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Problem Possible Cause Remedy Troubleshooting GuideOperation Page Maintenance Section Lubrication MaintenanceProper Torque For Fasteners  Limited WarrantyTo the OWNER/OPERATOR/DEALER Series Rear Mounted Blade