Bush Hog FC-0014 manual Maintenance and Service Safety Instructions and Practices

Page 16
(SG-2)
(SNPO-37)
(SL-39)
(SL-34)
(SL-21)

SAFETY

SAFETY

Do not raise the loader on a hillside. Do not transport across a slope with a raised loader. When the loader is raised, the center of gravity of the tractor and loader is raised increasing the potential for the tractor to tip over. Tractor wheel contact with any wash out, drop off or the ground obstruction with a raised loader could result in the tractor tipping over and causing serious bodily injury.

Lower the loader to the bed of the truck or trailer when transporting the tractor and loader with a truck. Measure to ensure the transport height does not exceed the legal limits. Contact with overhead obstructions or power lines can cause property damage or serious injury.

In case of mechanical difficulty during operation, place the transmission in the park position, set the parking brake, shut down all power, including the PTO and the engine and remove the key. Wait until all rotating motion has stopped before dismounting. (SG-39)

Transport an empty bale spear tilted back in the vertical position to prevent unintended harm to a person, animal or object. Serious injury or death may occur from a bale spear puncture.

Never drive the power unit with the bucket or plow in the raised position. Traveling with the bucket or plow in the raised position increases the chances of colliding with overhead obstructions and making the unit more prone to tipping over.

Maintenance and Service Safety Instructions and Practices

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards.

Never interfere with factory-set hydraulic calibrations. Any change in calibration could cause a failure of the equipment and may result in injury. (SBH-13)

Always maintain the safety signs in good readable condition. If the safety signs are missing, damaged, or unreadable, obtain and install replacement safety signs immediately. (SG-5)

2647 01/11

Safety Section 1-12

© 2011 Alamo Group Inc.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents 2647 To the Owner/Operator/Dealer Table of Contents Page Safety Section Safety General Safety Instructions and Practices2647 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 2647 01/11 Safety Section Safety Storage and Parking Safety Instructions and Practices Concluding Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Logo Bush HOG 3.20 x Safety Federal Laws and Regulations Employer-Employee Operator RegulationsPage Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Assembly InstructionsProper Ballasting and Wheel Spacing Installing Bucket Installing Mounting BracketsInstalling Bucket Level Indicator Dismounting and Mounting Loader Dismounting LoaderMounting Loader When Connecting an Attachment to the Loader Quick Hitch Quick Attach Device OptionalAssembly Operation Section Operation Bush Hog 2647 LoaderStandard Equipment and Specifications Operator Requirements Operation Tractor Requirements Personal Protective Equipment PPETractor Lighting and SMV Emblem Rops and Seat BeltTractor Ballast Getting On and Off the Tractor Boarding the TractorDismounting the Tractor Starting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/ServiceOperation Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation SL-33 Operation Operating the Loader Filling the BucketLifting the Load Carrying the Load Dumping the Bucket Lowering the BucketOperating with Float Control Loading from a BankOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Loader Storage Transporting the Tractor and ImplementOperation Transporting on Public Roadways Operation Troubleshooting Guide Operation Page Maintenance Section Maintenance See Your Bush HOG Dealer Lubrication Schedule Daily Maintenance Hydraulic Pressure CheckCylinder Service Lift Cylinder DisassemblyLift Cylinder Reassembly Bucket Cylinder Disassembly Slides over the wire retaining ring grooveBucket Cylinder Reassembly StorageMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty To the OWNER/OPERATOR/DEALER SOM-01/11 Printed U.S.A

FC-0014 specifications

The Bush Hog FC-0014 is a highly revered implement in the agricultural sector, known for its robust design and versatility. This rotary cutter is engineered for optimal performance, making it an essential tool for professionals and landowners alike. One of the main features of the FC-0014 is its exceptional cutting capacity, equipped with a 14-foot cutting width that enables it to cover large areas efficiently. This feature significantly reduces the time required for mowing large fields, pastures, and overgrown lands.

The FC-0014 utilizes a heavy-duty frame that ensures durability and stability during operation. Constructed from high-strength steel, the frame is designed to withstand tough conditions and frequent use, providing reliability for years to come. Another key characteristic of this rotary cutter is its advanced blade design. The FC-0014 is fitted with sharp, heat-treated blades that offer superior cutting performance. This design allows for cleaner cuts, ensuring that grass and vegetation are efficiently trimmed, promoting healthy regrowth.

Additionally, the Bush Hog FC-0014 boasts a unique lift design that provides exceptional ground clearance. This feature enhances the cutter's ability to navigate uneven terrain without difficulty. The adjustable cutting height allows operators to finely tune the mower's performance according to their specific land needs, ranging from low maintenance lawns to taller grass and brush.

Also noteworthy is the FC-0014’s compatibility with various tractor models thanks to its standard Category I and II hitching options. This versatility ensures that users can pair the cutter with the appropriate tractor, maximizing performance and efficiency.

Moreover, Bush Hog incorporates safety as a priority with the FC-0014. The cutter is designed with protective features that minimize the risk of debris being thrown during operation.

In summary, the Bush Hog FC-0014 stands out due to its impressive cutting width, durable construction, advanced blade technology, and safety features. This rotary cutter epitomizes efficiency and reliability, making it a preferred choice for land management and maintenance tasks. With its robust design and versatile capabilities, the FC-0014 continues to be a valuable asset to those looking to maintain their landscapes effectively.
Top Page Image Contents