Bush Hog FC-0014 manual Storage, Bucket Cylinder Reassembly

Page 89
(SL-27)
(SL-26)

MAINTENANCE

Bucket Cylinder Reassembly

Note: Be careful to not damage seals, packings and o-rings on the edges or holes in cylinder tube. Inspect and remove burrs and sharp edges if necessary before reassembling.

1.Place new v-pack set (5) in head (6).

Note: Lips on v-pack must face toward the insid eof head.

2.Place reinforcement washer (4) on top of v-pack set (5) and force down below snap ring groove.

3.Install snap ring (3) into snap ring groove.

Note: Rounded outside edge of snap ring must face inward and snap ring must be firmly seated in groove.

4.Install wiper seal (2) with lip of seal facing out and flush with top of cylinder head (6).

5.Place back-up washer (7) and o-ring (8) in groove on outside of head (6).

6.Remove sharp edges on outer edge of threaded end of shaft (1). Lubricate wiper seal (2) and v-packing (5) in head and carefully slide head (6) onto shaft.

7.Place o-ring (10), piston seal (11) and piston wear ring (12) in grooves on outside of piston (9). Note: For easier installation, place piston seal (10) in 120°F water to warm seal.

8.Slide piston (9) onto threaded end of shaft and install 3/4 elastic lock nut (13) to 300 ft./lbs.

9.Lubricate piston wear ring (12) and piston seal (11) on piston (9) and o-ring (8) on head (6) and carefully slide piston and head into cylinder tube (15).

10.Turn cylinder head (6) until hole in wire ring groove appears in slot in cylinder tube (15). Insert hook end of wire ring (14) into hole and turn cylinder head to thread wire ring into groove.

Storage

Never crawl under or allow children to play around or on a loader that is disconnected from the tractor. The loader could fall crushing a person resulting in serious injury or death. (SL-13)

Do not remove the attachment from the loader when the loader is disconnected from the tractor. The attachment stabilizes the loader. If the attachment is removed, the loader will fall and could result in serious injury.

Only disconnect and store the loader on firm flat ground. Make sure the loader stands are properly installed and rest on firm ground or support blocks. If the stands sink or fail, the loader could fall causing serious injury.

2647 01/11

Maintenance Section 5-9

© 2011 Alamo Group Inc.

MAINTENANCE

Page 88 Page 90
Image 89
Page 88 Page 90
Contents 2647 To the Owner/Operator/Dealer Table of Contents Page Safety Section General Safety Instructions and Practices Safety2647 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 2647 01/11 Safety Section Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Logo Bush HOG 3.20 x Safety Employer-Employee Operator Regulations Federal Laws and RegulationsPage Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions AssemblyProper Ballasting and Wheel Spacing Installing Bucket Level Indicator Installing Mounting BracketsInstalling Bucket Dismounting Loader Dismounting and Mounting LoaderMounting Loader Quick Attach Device Optional When Connecting an Attachment to the Loader Quick HitchAssembly Operation Section Bush Hog 2647 Loader OperationStandard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor RequirementsTractor Ballast Rops and Seat BeltTractor Lighting and SMV Emblem Boarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Tractor Pre-Operation Inspection/Service Pre-Operation Inspection and ServiceOperation Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation SL-33 Operation Filling the Bucket Operating the LoaderLifting the Load Carrying the Load Lowering the Bucket Dumping the BucketLoading from a Bank Operating with Float ControlOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Transporting the Tractor and Implement Loader StorageOperation Transporting on Public Roadways Operation Troubleshooting Guide Operation Page Maintenance Section Maintenance See Your Bush HOG Dealer Lubrication Schedule Hydraulic Pressure Check Daily MaintenanceLift Cylinder Disassembly Cylinder ServiceLift Cylinder Reassembly Slides over the wire retaining ring groove Bucket Cylinder DisassemblyStorage Bucket Cylinder ReassemblyMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty To the OWNER/OPERATOR/DEALER SOM-01/11 Printed U.S.A

FC-0014 specifications

The Bush Hog FC-0014 is a highly revered implement in the agricultural sector, known for its robust design and versatility. This rotary cutter is engineered for optimal performance, making it an essential tool for professionals and landowners alike. One of the main features of the FC-0014 is its exceptional cutting capacity, equipped with a 14-foot cutting width that enables it to cover large areas efficiently. This feature significantly reduces the time required for mowing large fields, pastures, and overgrown lands.

The FC-0014 utilizes a heavy-duty frame that ensures durability and stability during operation. Constructed from high-strength steel, the frame is designed to withstand tough conditions and frequent use, providing reliability for years to come. Another key characteristic of this rotary cutter is its advanced blade design. The FC-0014 is fitted with sharp, heat-treated blades that offer superior cutting performance. This design allows for cleaner cuts, ensuring that grass and vegetation are efficiently trimmed, promoting healthy regrowth.

Additionally, the Bush Hog FC-0014 boasts a unique lift design that provides exceptional ground clearance. This feature enhances the cutter's ability to navigate uneven terrain without difficulty. The adjustable cutting height allows operators to finely tune the mower's performance according to their specific land needs, ranging from low maintenance lawns to taller grass and brush.

Also noteworthy is the FC-0014’s compatibility with various tractor models thanks to its standard Category I and II hitching options. This versatility ensures that users can pair the cutter with the appropriate tractor, maximizing performance and efficiency.

Moreover, Bush Hog incorporates safety as a priority with the FC-0014. The cutter is designed with protective features that minimize the risk of debris being thrown during operation.

In summary, the Bush Hog FC-0014 stands out due to its impressive cutting width, durable construction, advanced blade technology, and safety features. This rotary cutter epitomizes efficiency and reliability, making it a preferred choice for land management and maintenance tasks. With its robust design and versatile capabilities, the FC-0014 continues to be a valuable asset to those looking to maintain their landscapes effectively.
Top Page Image Contents