Bush Hog FC-0014 manual Operation

Page 75
(SG-19)

OPERATION

Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and

how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement. As you increase the speed of the Tractor the stopping distance increases. Determine the maximum transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that the equipment can be operated at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum turning speed for you and this equipment before operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy.

Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind when you finish working in an area. Therefore, the operator must employ good judgement and safe operation practices when transporting the tractor and implement between locations. By using good judgement and following safe transport procedures, the possibility of accidents while moving between locations can be substantially minimized. OPS-L- 0031

2647 01/11

Operation Section 4-35

© 2011 Alamo Group Inc.

OPERATION

Page 74 Page 76
Image 75
Page 74 Page 76
Contents 2647 To the Owner/Operator/Dealer Table of Contents Page Safety Section General Safety Instructions and Practices Safety2647 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 2647 01/11 Safety Section Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Logo Bush HOG 3.20 x Safety Employer-Employee Operator Regulations Federal Laws and RegulationsPage Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions AssemblyProper Ballasting and Wheel Spacing Installing Mounting Brackets Installing BucketInstalling Bucket Level Indicator Dismounting Loader Dismounting and Mounting LoaderMounting Loader Quick Attach Device Optional When Connecting an Attachment to the Loader Quick HitchAssembly Operation Section Bush Hog 2647 Loader OperationStandard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor RequirementsRops and Seat Belt Tractor Lighting and SMV EmblemTractor Ballast Boarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Tractor Pre-Operation Inspection/Service Pre-Operation Inspection and ServiceOperation Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation SL-33 Operation Filling the Bucket Operating the LoaderLifting the Load Carrying the Load Lowering the Bucket Dumping the BucketLoading from a Bank Operating with Float ControlOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Transporting the Tractor and Implement Loader StorageOperation Transporting on Public Roadways Operation Troubleshooting Guide Operation Page Maintenance Section Maintenance See Your Bush HOG Dealer Lubrication Schedule Hydraulic Pressure Check Daily MaintenanceLift Cylinder Disassembly Cylinder ServiceLift Cylinder Reassembly Slides over the wire retaining ring groove Bucket Cylinder DisassemblyStorage Bucket Cylinder ReassemblyMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty To the OWNER/OPERATOR/DEALER SOM-01/11 Printed U.S.A

FC-0014 specifications

The Bush Hog FC-0014 is a highly revered implement in the agricultural sector, known for its robust design and versatility. This rotary cutter is engineered for optimal performance, making it an essential tool for professionals and landowners alike. One of the main features of the FC-0014 is its exceptional cutting capacity, equipped with a 14-foot cutting width that enables it to cover large areas efficiently. This feature significantly reduces the time required for mowing large fields, pastures, and overgrown lands.

The FC-0014 utilizes a heavy-duty frame that ensures durability and stability during operation. Constructed from high-strength steel, the frame is designed to withstand tough conditions and frequent use, providing reliability for years to come. Another key characteristic of this rotary cutter is its advanced blade design. The FC-0014 is fitted with sharp, heat-treated blades that offer superior cutting performance. This design allows for cleaner cuts, ensuring that grass and vegetation are efficiently trimmed, promoting healthy regrowth.

Additionally, the Bush Hog FC-0014 boasts a unique lift design that provides exceptional ground clearance. This feature enhances the cutter's ability to navigate uneven terrain without difficulty. The adjustable cutting height allows operators to finely tune the mower's performance according to their specific land needs, ranging from low maintenance lawns to taller grass and brush.

Also noteworthy is the FC-0014’s compatibility with various tractor models thanks to its standard Category I and II hitching options. This versatility ensures that users can pair the cutter with the appropriate tractor, maximizing performance and efficiency.

Moreover, Bush Hog incorporates safety as a priority with the FC-0014. The cutter is designed with protective features that minimize the risk of debris being thrown during operation.

In summary, the Bush Hog FC-0014 stands out due to its impressive cutting width, durable construction, advanced blade technology, and safety features. This rotary cutter epitomizes efficiency and reliability, making it a preferred choice for land management and maintenance tasks. With its robust design and versatile capabilities, the FC-0014 continues to be a valuable asset to those looking to maintain their landscapes effectively.
Top Page Image Contents