Bush Hog FC-0014 manual Lift Cylinder Reassembly

Page 87

MAINTENANCE

Lift Cylinder Reassembly

Note: Be careful not to damage seals and o-rings on edges or holes in cylinder tube. Inspect and remove burrs and sharp edges if necessary before reassembly.

1.Place o-ring part of rod seal (3) into groove inside of head (5) and position it against the side of the groove toward the cylinder tube end.

2.Press one side of the L-seal part of the rod seal (3) past its center until it touches the opposite side, then press the two ends of this shape together as necessary to fit into the bore of the cylinder head. With the seal compressed in this manner, and with the lips toward the cylinder tube end, push it down the bore of the cylinder head. When it reaches the groove, allow it to expand to its original shape within the groove.

Note: Lips of seal (3) must be face inward and seal must be firmly seated in groove.

3.Install wiper seal (2) with lip of seal facing out and flush with top of cylinder head (5).

4.Place o-ring (4) in groove on outside of head (5).

5.Remove sharp edges on outer edge of the threaded end of shaft (1). Lubricate wiper seal (2) and rod seal

(3) in head and carefully slide head (5) onto shaft.

6.Place o-ring (10), piston seal (11) and piston wear ring (8) in grooves on outside of piston (9). Note: For easier installation, place piston seal (11) in 120°F water to warm seal.

7.Slide piston (6) onto threaded end of shaft and install 3/4 elastic lock nut (10) to 100 lbs.

8.Lubricate piston wear ring (9) and piston seal (8) on piston (6), o-ring (4) on head (5), then carefully slide piston and head into cylinder tube (11).

9.Insert wire retaining ring (12) into slot in the cylinder tube and turn cylinder head while applying pressure to wire ring to thread it into the groove.

Note: If cylinder has a countersunk hole, hook end of retaining wire into hole and turn cylinder head 1-1/2 turns to secure wire. End of hook may need to be ground to fit in countersunk hole.

2647 01/11

Maintenance Section 5-7

© 2011 Alamo Group Inc.

MAINTENANCE

Page 86 Page 88
Image 87
Page 86 Page 88
Contents 2647 To the Owner/Operator/Dealer Table of Contents Page Safety Section General Safety Instructions and Practices Safety2647 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 2647 01/11 Safety Section Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Logo Bush HOG 3.20 x Safety Employer-Employee Operator Regulations Federal Laws and RegulationsPage Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions AssemblyProper Ballasting and Wheel Spacing Installing Mounting Brackets Installing BucketInstalling Bucket Level Indicator Dismounting Loader Dismounting and Mounting LoaderMounting Loader Quick Attach Device Optional When Connecting an Attachment to the Loader Quick HitchAssembly Operation Section Bush Hog 2647 Loader OperationStandard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor RequirementsRops and Seat Belt Tractor Lighting and SMV EmblemTractor Ballast Boarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Tractor Pre-Operation Inspection/Service Pre-Operation Inspection and ServiceOperation Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation SL-33 Operation Filling the Bucket Operating the LoaderLifting the Load Carrying the Load Lowering the Bucket Dumping the BucketLoading from a Bank Operating with Float ControlOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Transporting the Tractor and Implement Loader StorageOperation Transporting on Public Roadways Operation Troubleshooting Guide Operation Page Maintenance Section Maintenance See Your Bush HOG Dealer Lubrication Schedule Hydraulic Pressure Check Daily MaintenanceLift Cylinder Disassembly Cylinder ServiceLift Cylinder Reassembly Slides over the wire retaining ring groove Bucket Cylinder DisassemblyStorage Bucket Cylinder ReassemblyMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty To the OWNER/OPERATOR/DEALER SOM-01/11 Printed U.S.A

FC-0014 specifications

The Bush Hog FC-0014 is a highly revered implement in the agricultural sector, known for its robust design and versatility. This rotary cutter is engineered for optimal performance, making it an essential tool for professionals and landowners alike. One of the main features of the FC-0014 is its exceptional cutting capacity, equipped with a 14-foot cutting width that enables it to cover large areas efficiently. This feature significantly reduces the time required for mowing large fields, pastures, and overgrown lands.

The FC-0014 utilizes a heavy-duty frame that ensures durability and stability during operation. Constructed from high-strength steel, the frame is designed to withstand tough conditions and frequent use, providing reliability for years to come. Another key characteristic of this rotary cutter is its advanced blade design. The FC-0014 is fitted with sharp, heat-treated blades that offer superior cutting performance. This design allows for cleaner cuts, ensuring that grass and vegetation are efficiently trimmed, promoting healthy regrowth.

Additionally, the Bush Hog FC-0014 boasts a unique lift design that provides exceptional ground clearance. This feature enhances the cutter's ability to navigate uneven terrain without difficulty. The adjustable cutting height allows operators to finely tune the mower's performance according to their specific land needs, ranging from low maintenance lawns to taller grass and brush.

Also noteworthy is the FC-0014’s compatibility with various tractor models thanks to its standard Category I and II hitching options. This versatility ensures that users can pair the cutter with the appropriate tractor, maximizing performance and efficiency.

Moreover, Bush Hog incorporates safety as a priority with the FC-0014. The cutter is designed with protective features that minimize the risk of debris being thrown during operation.

In summary, the Bush Hog FC-0014 stands out due to its impressive cutting width, durable construction, advanced blade technology, and safety features. This rotary cutter epitomizes efficiency and reliability, making it a preferred choice for land management and maintenance tasks. With its robust design and versatile capabilities, the FC-0014 continues to be a valuable asset to those looking to maintain their landscapes effectively.
Top Page Image Contents