Bush Hog FC-0014 manual Daily Maintenance, Hydraulic Pressure Check

Page 85

MAINTENANCE

Daily Maintenance

Regular maintenance of your loader and hydraulic system will insure maximum loader efficiency and long life.

1.Check fluid level of tractor hydraulic system before starting each day’s operation. If necessary, add hydraulic oil as recommended in your tractor operator’s manual.

2.After every ten hours of operation, lubricate all twelve grease fittings; one at each end of lift boom arms and one at rod and base ends of each lift and bucket cylinder.

3.After every ten hours of operation, check all hardware and tighten where required.

4.Replace hoses immediately if they are damaged by a cut or scrape, extruded at the fittings or leaking. Hydraulic oil leaks should be repaired promptly to avoid loss of oil and serious personal injury from escaping oil.

Hydraulic Pressure Check

Following procedure outlines hydraulic pressure check.

1.Obtain a pressure gauge that measures 3000 PSI in 50 PSI increments.

2.Install gauge into the hydraulic line connecting the loader valve and to the base port of bucket cylinders.

3.Start engine and adjust to 1700-2200 RPM.

4.Push bucket control lever to pressurize the hydraulic line with the gauge attached. Hold the control until the cylinders reach the fully extended position. Holding the control with cylinders fully extended will give you the hydraulic system pressure on the gauge.

5.If pressure is not correct, refer to “TROUBLESHOOTING” Section for possible remedy or contact your dealer.

Escaping hydraulic fluid under pressure can penetrate skin, causing serious personal injury.

•DO NOT use your hand to check for leaks. Use a piece of wood or cardboard and wear eye protection to search for leaks.

•Stop engine and relieve pressure before connecting or disconnecting lines.

•Tighten all connections before starting engine or pressurizing lines.

NOTE: If any fluid is injected into skin, obtain medical attention immediately or gangrene may result.

2647 01/11

Maintenance Section 5-5

© 2011 Alamo Group Inc.

MAINTENANCE

Page 84 Page 86
Image 85
Page 84 Page 86
Contents 2647 To the Owner/Operator/Dealer Table of Contents Page Safety Section General Safety Instructions and Practices Safety2647 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety SL-33 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices 2647 01/11 Safety Section Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Logo Bush HOG 3.20 x Safety Employer-Employee Operator Regulations Federal Laws and RegulationsPage Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions AssemblyProper Ballasting and Wheel Spacing Installing Bucket Installing Mounting BracketsInstalling Bucket Level Indicator Dismounting Loader Dismounting and Mounting LoaderMounting Loader Quick Attach Device Optional When Connecting an Attachment to the Loader Quick HitchAssembly Operation Section Bush Hog 2647 Loader OperationStandard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Tractor RequirementsTractor Lighting and SMV Emblem Rops and Seat BeltTractor Ballast Boarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Tractor Pre-Operation Inspection/Service Pre-Operation Inspection and ServiceOperation Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation SL-33 Operation Filling the Bucket Operating the LoaderLifting the Load Carrying the Load Lowering the Bucket Dumping the BucketLoading from a Bank Operating with Float ControlOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Transporting the Tractor and Implement Loader StorageOperation Transporting on Public Roadways Operation Troubleshooting Guide Operation Page Maintenance Section Maintenance See Your Bush HOG Dealer Lubrication Schedule Hydraulic Pressure Check Daily MaintenanceLift Cylinder Disassembly Cylinder ServiceLift Cylinder Reassembly Slides over the wire retaining ring groove Bucket Cylinder DisassemblyStorage Bucket Cylinder ReassemblyMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty To the OWNER/OPERATOR/DEALER SOM-01/11 Printed U.S.A

FC-0014 specifications

The Bush Hog FC-0014 is a highly revered implement in the agricultural sector, known for its robust design and versatility. This rotary cutter is engineered for optimal performance, making it an essential tool for professionals and landowners alike. One of the main features of the FC-0014 is its exceptional cutting capacity, equipped with a 14-foot cutting width that enables it to cover large areas efficiently. This feature significantly reduces the time required for mowing large fields, pastures, and overgrown lands.

The FC-0014 utilizes a heavy-duty frame that ensures durability and stability during operation. Constructed from high-strength steel, the frame is designed to withstand tough conditions and frequent use, providing reliability for years to come. Another key characteristic of this rotary cutter is its advanced blade design. The FC-0014 is fitted with sharp, heat-treated blades that offer superior cutting performance. This design allows for cleaner cuts, ensuring that grass and vegetation are efficiently trimmed, promoting healthy regrowth.

Additionally, the Bush Hog FC-0014 boasts a unique lift design that provides exceptional ground clearance. This feature enhances the cutter's ability to navigate uneven terrain without difficulty. The adjustable cutting height allows operators to finely tune the mower's performance according to their specific land needs, ranging from low maintenance lawns to taller grass and brush.

Also noteworthy is the FC-0014’s compatibility with various tractor models thanks to its standard Category I and II hitching options. This versatility ensures that users can pair the cutter with the appropriate tractor, maximizing performance and efficiency.

Moreover, Bush Hog incorporates safety as a priority with the FC-0014. The cutter is designed with protective features that minimize the risk of debris being thrown during operation.

In summary, the Bush Hog FC-0014 stands out due to its impressive cutting width, durable construction, advanced blade technology, and safety features. This rotary cutter epitomizes efficiency and reliability, making it a preferred choice for land management and maintenance tasks. With its robust design and versatile capabilities, the FC-0014 continues to be a valuable asset to those looking to maintain their landscapes effectively.
Top Page Image Contents