Bush Hog 965H, 665H, 865H For Tractors with OPEN-CENTER Hydraulic Systems, Tractor Preparation

Page 32

TORQUE VALUES

Common bolts and nuts

 

 

Tightening Torque Plus/Minus 20%

 

 

 

 

 

Size

Grade 2

Grade 5

Grade 8

 

 

 

 

 

 

1/4-20 NC

70 in. lbs.

115 in. lbs.

165 in. lbs.

1/4-28 NF

85 in. lbs.

140 in. lbs.

200 in. lbs.

5/16-18 NC

150 in. lbs.

250 in. lbs.

350 in. lbs.

5/16-24 NF

165 in. lbs.

270 in. lbs.

30 ft. lbs.

3/8-16 NC

260 in. lbs.

35 ft. lbs.

50 ft. lbs.

3/8-24 NF

300 in. lbs.

40 ft. lbs.

60 ft. lbs.

7/16-14 NC

35 ft. lbs.

55 ft. lbs.

80 ft. lbs.

7/16-20 NF

45 ft. lbs.

75 ft. lbs.

105 ft. lbs.

1/2-13 NC

50 ft. lbs.

80 ft. lbs.

115 ft. lbs.

1/2-20 NF

70 ft. lbs.

105 ft. lbs.

165 ft. lbs.

9/16-12 NC

75 ft. lbs.

125 ft. lbs.

175 ft. lbs.

9/16-18 NF

100 ft. lbs.

165 ft. lbs.

230 ft. lbs.

5/8-11 NC

110 ft. lbs.

180 ft. lbs.

260 ft. lbs.

5/8-18 NF

140 ft. lbs.

230 ft. lbs.

330 ft. lbs.

3/4-10 NC

150 ft. lbs.

245 ft. lbs.

350 ft. lbs.

3/4-16 NF

200 ft. lbs.

325 ft. lbs.

470 ft. lbs.

Note - See tractor instruction manual or your tractor dealer for tightening of metric bolts.

POWER BEYOND KITS

FOR TRACTORS WITH OPEN-CENTER HYDRAULIC SYSTEMS

General Description

A power beyond application is required to convert a hydraulic valve so that pressurized oil can be directed to another “open center” valve. This allows the back- hoe valve and a loader valve, or other accessory, to be connected to the tractor hydraulic system simulta- neously, without the inconvenience of using a flow diverting valve.

Since the power beyond application is only required on “open center” hydraulic systems, oil will be con- stantly flowing from the pump through the backhoe and loader or other accessory valve, and then back to the reservoir. “Open center” refers to this constant flow through the open center of the valves.

The assembly instructions cover two conditions that require a power beyond kit to be ordered from Bush Hog. The first procedure shows the recommended method of connecting a Bush Hog loader with a Bush Hog valve to a Bush Hog backhoe. The second pro- cedure shows the recommended method for connect- ing a Bush Hog backhoe and a competitive loader or a non Bush Hog valve. The second is also used to operate the backhoe and loader off the backhoe PTO pump kit option. The power beyond plug is included with the loader valve when the valve is ordered. The second procedure requires the power beyond kit for

the backhoe valve be ordered from Bush Hog as a separate item.

The hoses and fittings required in either procedure to connect the two valves together are not supplied. The proper fittings and hose lengths required must be determined for each specific application. The parts must be supplied by the customer.

Tractor Preparation

Stop tractor, lower all attachments to the ground, and relieve pressure in all hydraulic lines by moving all control handles back and forth or side to side several times.

Backhoe Preparation

1. Remove shroud covering valve hydraulic fittings.

Note: The terms RIGHT and LEFT for all adapter parts are determined from the position of the operator when seated in the operating position on the backhoe.

2.Carefully clean the top and right side of the back- hoe control valve and remove the “conversion” plug located in the center of the right side of the valve.

Note: If there are two plugs in this area, the conver- sion plug is the larger plug located lower on the right side of the valve.

30

Image 32
Contents Bush HOG Congratulations Backhoes This Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List 665H 765H 865H 965H BackhoesTractor BackhoeAvoid HIGH-PRESSURE Fluids Adjustments and InspectionTransportation Safety Decals Employee Tractor Operating Instructions This Act SeeksOsha Regulations Child Labor Under 16 Years OldControls Keep bystanders a safe distance awayEngine Speed Page Transporting the Backhoe When Transporting Placing the StabilizersFilling the Bucket Dumping the BucketSide Slope Excavating or Trenching MiscellaneousFinishing Straight Walls BackfillingBeginning of Season Bleeding Backhoe Hydraulic SystemHydraulic System Hoses Hydraulic System ReservoirLubrication Tooth ReplacementTightening Nuts and Bolts Install the swing safety lock pin as shown in Figures 1 Removal from Tractor StorageHydraulic Trouble Shooting Stabilizer Pads 765H, 865H and 965HCauses and Corrections Replace Center Section Assemblies Replacing Spool SealsAssembly Be sure hoist Used is suitable, has suffi Cient capacity and is in the proper position. DoDo not cut any strapping that fastens the back Hoe mainframe and swing frame to the skid atAssembly Refer to Figures 13 Attaching KIT Instructions For 865H General DescriptionAssembly Hydraulic Hook-Up Closed Center System 665H &765H Hook-Up Diagram Hydraulic Hook-Up 865H & 965HHook-Up Requirements Backhoe OperationAttaching KIT Instructions For 965H Assembly Refer to Backhoe Preparation For Tractors with OPEN-CENTER Hydraulic SystemsTractor Preparation Assembly of a Bush HOG Backhoe to a Bush HOG Loader Valve Bush HOG Backhoe & Bush HOG Loader Valve Assembly Outlet Assembly 10 .5 GPM PTO Pump KITOr 8 GPM PTO Pump KIT 11 .5 GPM PTO Pump KITGPM Pump KIT Pump Plate PositionsSeries Models 665H and 765H Models 865H Shown 965H Page Bush HOG, L.L.C
Related manuals
Manual 1 pages 22.78 Kb