3. Remove plastic bag containing bucket pins from |
| 6. Attach stabilizer cylinders (H) to stabilizers using |
backhoe. Attach bucket (D) to dipperstick using one |
| pins and hardware assembled to stabilizers. |
pin, two bolts, nuts, lockwashers, pin retainers and |
| 7. Using caution to prevent tipping, raise mainframe |
washers as necessary. |
| |
| with hoist to a height of approximately 11” for 862H | |
4. Attach bucket link (E) to bucket, using same hard- |
| |
| and 13” for 962H and remove skid. Block mainframe | |
ware as listed for step #3. |
| (G) and swing frame (I) securely. |
5. Attach hoist to backhoe to prevent tipping. Remove |
| 8. Follow the Attaching Kit Assembly Instructions to |
all remaining strapping and attach stabilizers (F) to |
| mount the backhoe to the tractor. Check the installa- |
mainframe (G) using pins and hardware assembled to |
| tion carefully and make sure that all members are cor- |
backhoe. |
| rectly installed and securely fastened. |
|
|
|
|
|
|
|
|
|
Assembly:(665H & 765H) - Figure 12 |
|
|
| CAUTION |
|
|
| |||||||
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
| Be sure hoist |
| used is suitable, has suffi- | |||||
(See “General” note, page 20) | being | |||||||||||||
cient capacity and is in the proper position. Do | ||||||||||||||
|
|
|
|
|
|
| ||||||||
IMPORTANT: Tighten all hardware to torque | not allow anyone under a backhoe member sup- | |||||||||||||
ported by hoist. | ||||||||||||||
requirements specified in torque chart. | ||||||||||||||
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
| 3. Remove plastic bag containing bucket pins from | |||||||
|
|
| CAUTION |
|
|
| backhoe. Attach Bucket (D) to Dipperstick using one | |||||||
|
|
|
|
|
| |||||||||
|
|
|
|
|
| pin, two bolts, locknuts, pin retainers, and washers as | ||||||||
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
| ||||||||
DO NOT cut any strapping that fastens the back- | ||||||||||||||
needed to take up gap under pin retainers. | ||||||||||||||
hoe mainframe and swing frame to the skid at | 4. Attach Bucket Link (E) to Bucket, using same | |||||||||||||
this time. | ||||||||||||||
|
|
|
|
|
|
| hardware as listed for step #3. | |||||||
1. Remove the stabilizer assemblies and any miscella- | 5. Reposition hoist on backhoe to prevent tipping and | |||||||||||||
neous items which have been fastened to skid and | ||||||||||||||
raise Mainframe slightly. Remove all remaining strap- | ||||||||||||||
arrange conveniently. Reposition stabilizer cylinders from | ||||||||||||||
ping and crate base. Using caution to prevent tipping, | ||||||||||||||
their shipping configuration, by assembling them into the | ||||||||||||||
raise Mainframe (G) approximately 10” and block | ||||||||||||||
mainframe, using the hardware provided. Be sure cylinder | ||||||||||||||
Mainframe and Swing Frame securely. | ||||||||||||||
ports are pointed upward and hoses are routed above the | ||||||||||||||
|
|
|
|
|
|
| ||||||||
cylinder to mainframe pivot pin connection. Refer to page 36. | 6. Attach Stabilizers (F) to Mainframe (G) using pins | |||||||||||||
|
|
|
|
|
|
| and hardware assembled to Stabilizers (F). | |||||||
2. Support Boom (A) and Dipperstick (B) with hoist | 7. Attach Stabilizer Cylinders (H) to stabilizers (F) | |||||||||||||
and remove Boom transport lock pin. Lower Boom | using pins and hardware assembled to Stabilizers (F). | |||||||||||||
and manually extend Dipperstick until it rests on the |
|
|
|
|
|
|
|
ground. Move control handle to “Boom Down” position | 8. Follow the Attaching Kit Assembly Instructions to | |
mount the backhoe to the tractor. Check the installa- | ||
as required to aid movement. | ||
tion carefully and make sure that all members are cor- | ||
| ||
| rectly installed and securely fastened. |
ATTACHING KIT INSTRUCTIONS (For 665H & 765H)
TO TRACTOR HYDRAULIC SYSTEMS
General Description
Mounting and hydraulics kits include two hoses which can be used to connect the backhoe to the tractor hydraulic system. Additional hydraulic components or kits will be required to complete the
The backhoe is mounted on the tractor lower link arms and an adjustable upper link is supplied to replace the tractor upper link. A set of stabilizer arms is included. They bolt from the adjustable upper link to the backhoe mainframe, locking the hoe rigidly in one position.
IMPORTANT: Tractor lower links must be kept free of lifting forces at all times after installation of the attaching kit, by keeping tractor quadrant lever in the lowered position.
IMPORTANT: If the
21